manualshive.com logo in svg

AB Regin Corrigo E81D-3, Manual, Page: 114 / 118

Share
Download
AB Regin Corrigo E81D-3 Manual Download Page 114

 

 

Appendix Frequency converters 

Version 3.3 of Corrigo ventilation supports the frequency converters listed below: 

•

 

Vacon NXL 

•

 

Lenze 

•

 

Omron V1000 

•

 

Emerson Commander 

•

 

LS 

•

 

EBM 

•

 

Danfoss FC 101 

When communicating via frequency converters through Modbus, it is sometimes necessary to 
change certain settings in the frequency converter. Below are described what settings are necessary 
in the various models: 

 

Vacon NXL 

No settings necessary. 

 

Lenze 

No settings necessary. 

 

Omron V1000 

Connected via RS485: 

•

 

R+ is connected to S+ 

•

 

R- is connected to S- 

•

 

R+/S+ is connected to B on port 1 or 2 

•

 

R-/S- is connected to A on port 1 or 2 

 

Parameters 

The following parameters must be set from the display of the frequency converter: 

•

 

H5-01 (0x425): Slave address, set to = 1 for Supply air fan and = 2 for Exhaust air fan 

•

 

H5-07 (0x42B): RTS Control, set to = 1 (enabled) for activation of RS485  

•

 

o1-03 (0x502): Frequency reference units, set to = 1 for 0-100%.  

•

 

H5-03 (0x427): Parity, set to = 0 (no parity) 

 

Default values should be used for remaining parameters. The following values may not be changed: 

•

 

H5-02 (0x426): Communication speed, default =3 (9600) 

•

 

H5-04 (0x428): Stopping method after communication error, default = 3 (no stop) 

•

 

H5-11 (0x43C): Communication Enter Function, default=1 (Enter command not 

Summary of Contents for Corrigo E81D-3























































































































Reviews:

No comments