AAON SS1079 Technical Manual Download Page 58

Page: 58 / 98

Zone

VCC-X STATUS

VCC-X Operator Interface SD

VCC-X Status Screens

Status Screen #9 - Heating Outputs - Active

Stages and Mod Heat Position

VCC-X v1.02 ID #

Heating Outputs

Active Stages: XX
Mod Heat Pos.: XXX%

Line 3 Heating Active Stages

This line will display the number of stages of Heating

that are currently active.

Line 4 Current Modulating Heating Output Signal
Percentage

Indicates the percentage output signal being supplied

to a Modulating Heating device when you have

con

gured this option for your HVAC unit.

Status Screen #10 - MODGAS-X Enabled and

Output %

VCC-X v1.02 ID #

MODGAS-X

Enabled: YES/NO

Position: XXX%

Line 3 MODGAS-X Enabled or Disabled

This indicates whether the VCC-X Controller has

enabled the MODGAS-X Controller to begin to operate.

If you do not have a MODGAS-X Controller connected

to the VCC-X Controller, this line will indicate “NO”.

Line 4 Current MODGAS-X Heating Output Signal

Indicates the percentage output signal being supplied

by the MODGAS-X controller when you have one

connected to the VCC-X Controller.

Status Screen #11 - Space RH & Indoor RH

Setpoint

VCC-X v1.02 ID #

Space RH: XXX.X%
Return RH: XXX.X%
RH Setpoint: XXX.X%

Line 2 Current Space Relative Humidity Percentage

If an E-BUS Space Temperature/Humidity Sensor has

been installed and con

gured on the unit, the current

Space Air Relative Humidity Percentage will appear on

this line. If this combination Temperature/Humidity

Sensor is not installed, this line will display 0%.

Line 3 Current Return Air Relative Humidity Percentage

If an E-BUS Return Air Temperature/Humidity Sensor

has been installed and con

gured on the unit, the current

Return Air Relative Humidity Percentage will appear on

this line. If this combination Temperature/Humidity

Sensor is not installed, this line will display 0%.

Line 4 Current Indoor Relative Humidity Setpoint
Percentage

This is the adjustable Indoor Air Relative Humidity

Setpoint Percentage that has been set by the user.

Status Screen #12 - MHGRV-X Enabled and

Output %

VCC-X v1.02 ID #

MHGRV-X

Enabled: YES/NO
Position: XXX%

Line 3 MHGRV-X Enabled or Disabled

This indicates whether the VCC-X Controller has

enabled the MHGRV-X Controller to begin to operate.

If you do not have a MHGRV-X Controller connected to

the VCC-X Controller, this line will indicate “NO”.

Line 4 Current MHGRV-X Reheat Valve Output Signal
Percentage

Indicates the percentage output signal being supplied
by the MHGRV-X Controller when you have one
connected to the VCC-X Controller.

Status Screen #13 - PREHEAT-X Controller

Status and Leaving Air Temperature Setpoint

VCC-X v1.02 ID #

Preheat-X

Enabled: YES/NO
Lvg Air Spt: 0.0

Line 3 PREHEAT-X Enabled or Disabled

This indicates whether the VCC-X Controller has

enabled the PREHEAT-X Controller to begin to operate.

If you do not have a PREHEAT-X Controller connected

to the VCC-X Controller, this line will indicate “NO”.

Line 4 Leaving Air Temperature Setpoint

This is the con

gured Leaving Air Temperature Setpoint.

Summary of Contents for SS1079



































































































Search results

Summary of Contents for SS1079

Reviews:

Related manuals for SS1079

Brands by name

Popular brands

AAON SS1079, Technical Manual

Search results

Summary of Contents for SS1079

Reviews:

Related manuals for SS1079

Brands by name

Popular brands