AAON SS1079 Technical Manual Download Page 56

Page: 56 / 98

Zone

VCC-X STATUS

VCC-X Operator Interface SD

VCC-X Status Screens

Status Screens - General Procedures

From any menu screen,

press

. The

Unit Selection Screen,

shown below,

will appear requesting that you enter the unit ID number.

Enter Unit Address

Then Press Enter

Selected Unit#: XXXX

No Communication

Enter

the correct unit ID number of the Controller you want to view

and

press

<ENTER>

. Once communication is established, “No Com-

munication” will be replaced with “Press Down.” Then

press



You will then see the

Status Selection Screen(s)

below:

VCC-X Status
RSM-VFD & HP Status
RSM DIGITAL Status
Select & Press Enter

Select

VCC-X Status. Then

press

<ENTER>

The

rst

VCC-X Status Screen

will appear.

Press



to scroll

through the screens.

NOTE:

If “No Communication” remains, it indicates a

communication failure to the controller.

Status Screen #1 - Date and Time

VCC-X v1.02 ID #
Controller Date/Time

01/16/2015 05:00 PM

Line 2 Controller Date/Time
Line 3

MM/DD/YYYY HH:MM XX

(Month, Day, Year) (Hour, Minutes, AM or PM)

Status Screen #2 - Application Type, Schedule

Mode & HVAC Mode

VCC-X v1.02 ID #

App Type

Schedule Mode

HVAC Mode

Line 2 App Type:

Constant

Volume

Single

Zone

VAV

w/Tempering

Make Up Air Space w/High OA%

Line 3

Schedule Mode:

Unoccupied Holiday Occupied

Occupied

Forced

Occupied

Override

Forced

Unoccupied

Holiday

Unoccupied

Remote

Occupied

Line 4 HVAC Mode:

Off

Dehum

Vent

Mode

Dehum

Cool

Mode

Dehum

Heat

Mode

Warm

Defrost

Cool

Down

Remote

Cool

Remote

Heat

Remote Vent RH Remote Cool RH

Remote

Heat

Status Screen #3 - Controlling Temperature,

Cooling & Heating Setpoints

VCC-X v1.02 ID #

Ctrl Temp: 0.0

Cool Spt: 0.0

Heat Spt: 0.0

Line 2

Controlling Temperature

This is the temperature of the sensor that is con

gured as

the HVAC Source (Mode Enable) Sensor. This can be

the Supply Air, Return Air, Outdoor Air, or Space

Temperature

Sensor.

Line 3

Cooling Setpoint

Based on the current Occupied/Unoccupied Mode

operation.

(Re

ects any active resets.)

Line 4 Heating Setpoint

Based on the current Occupied/Unoccupied Mode

of operation. (Re

ects any active resets.)

Summary of Contents for SS1079



































































































Search results

Summary of Contents for SS1079

Reviews:

Brands by name

Popular brands

AAON SS1079, Technical Manual

Search results

Summary of Contents for SS1079

Reviews:

Brands by name

Popular brands