manualshive.com logo in svg

3D Systems CubePro 3D Printer, User Manual, Page: 91 / 110

Share
Download
3D Systems CubePro 3D Printer User Manual Download Page 91

CALIBRATING THE OFFSET JETS

WARNING: DO NOT USE THE OFFSET JETS MENU UNLESS YOU HAVE BEEN ADVISED TO

DO SO BY CUBIFY SUPPORT. CHANGES TO THESE SETTINGS WILL AFFECT THE QUALITY

OF MULTI-COLOR OR MULTI-MATERIAL PRINTS. CALIBRATION WAS PERFORMED BY THE

FACTORY AND ANY CHANGES TO THESE SETTINGS MUST BE APPROVED AND GUIDED

BY CUBIFY SUPPORT.

NOTE: Calibrating the Offset Jets is only applicable for printers with more than one (1)

print jet installed.

Calibration files can be downloaded from 

www.3dsystems.com/shop/cubepro/downloads

. These files are

printed like any other .cubepro file. There are four files available. The files are specific for the model
printer (CubePro Duo or CubePro Trio) and for the material type (ABS or PLA) currently installed in the
printer. All installed cartridges must be same material type (ABS or PLA) and each print jet will be used.
Two Level Gap calibration files will also download with the Offset Jet Calibration files. These should be
ignored during this procedure.

Calibration Overview

Depending on your printer model, you may have up to three (3) print jets installed. Calibrating the offset
jets becomes necessary when multi-color or multi-material prints are not aligned properly. If the print jets
are not positioned properly, supports may not print as intended and print geometries may be altered.

When it becomes necessary to calibrate the offset jets, each print jet will be tested for proper alignment.
When printing the test file, a scale will be printed by all print jets and the scales printed by print jets 2 and
3 will be compared to the scale printed by print jet 1.

NOTE: It is very important to compare the scales printed by print jet 2 and print jet 3

to the scale printed by print jet 1. Print jet one should not be adjusted.

Y-Axis Scale

X-Axis Scale

Print Jet 3 Y-Axis Scale

Print Jet 2 X-Axis Scale

Print Jet 1 Y-Axis Scale

Print Jet 1 X-Axis Scale

Print Jet 2 Y-Axis Scale

Print Jet 3 X-Axis Scale

In the print scale illustration, the X+ scale (left-to-right) contains three (3) rows of printed lines. Each line
represents a print jet. The prints are numbered 1, 2 and 3 for each of the three print jets. Print jet 1 always

Summary of Contents for CubePro 3D Printer















































































































Reviews:

No comments