manualshive.com logo in svg

3D Systems CubePro 3D Printer, User Manual, Page: 54 / 110

Share
Download
3D Systems CubePro 3D Printer User Manual Download Page 54

PREPARING AND PRINTING A CREATION

WARNING: THE PRINT JETS BECOME EXTREMELY HOT DURING SETUP AND OPERATION.

DO NOT TOUCH THE PRINT JETS.

CAUTION: Do not change the material cartridge color or material type during printing.

Doing so may damage the printer.

The CubePro software client includes useful tools to place a creation in the optimum position for printing.
The model can be moved or rotated using the mouse.

Pan/Zoom: 

Rotate the mouse wheel in either direction

Rotate the Print Pad: 

Left-click and drag the mouse to change the view of the model

Move the Print Pad:

Right-click and drag the mouse to move the print pad.

Select 

Open Model

.

1.

NOTE: Select 

Open Model Assembly

 if there are multiple parts in the model.

Browse to the creation file and select 

Open

.

2.

NOTE: The creation or assembly will appear on the print pad.

NOTE: You can also open multiple creations on the same print pad.

NOTE: To open .cubepro files, select Open from the Print File menu, browse to the

creation file and select Open.

If your creation requires a single color, select the Single Color checkbox from the Home tab.

3.

Summary of Contents for CubePro 3D Printer















































































































Reviews:

No comments