manualshive.com logo in svg

3D Systems CubePro 3D Printer, User Manual, Page: 17 / 110

Share
Download
3D Systems CubePro 3D Printer User Manual Download Page 17

SETUP AND ACTIVATION

Select your language. Press the checkmark to confirm your selection.

1.

Enter a name for your printer. Scroll to the letters you wish to select by pressing the arrow symbols on each side of the screen. Press the letters to select

2.

them. Select the 

checkmark

 to continue. If you do not wish to name your CubePro, press 

SKIP

 to move to the next screen and continue with step 4.

NOTE: The printer will search for area wireless networks.

Connect your printer to your wireless network. Use the up or down arrow to scroll to your network choice. Select your network.

3.

NOTE: If your network is password protected, the printer will first prompt you to enter

the password.
NOTE: The printer can also connect to an ad hoc network, a decentralized network

that wirelessly connects a local computer to the printer directly. The computer must

have a wireless adapter configured for ad-hoc mode. The adapter must use the same

SSID as is found in the printer. Connecting to an ad hoc network is discussed further

in the section titled 

Setting Up an Ad Hoc Network

.

NOTE: Connection to a network is confirmed when a checkmark appears to the left of

the network name. If the network is secured, a lock icon will appear to the right of the

network name.

Summary of Contents for CubePro 3D Printer















































































































Reviews:

No comments