manualshive.com logo in svg

3D Systems CubePro 3D Printer, User Manual, Page: 25 / 110

Share
Download
3D Systems CubePro 3D Printer User Manual Download Page 25

Print Plate Calibration

MOVE JETS

 allows the user to manually move the print jets in the X and Y directions.

LEVEL PLATE

 is a utility that assists in leveling the print pad to the print jets.

Print Jet Calibration

CONTROL JETS

 allows the user to test the operation of the extruders and print jets.

OFFSET JETS

 is a utility that defines the parameters of the space between the print jets.

CAUTION: Do not change any of the values in the OFFSET JETS utility unless advised to

do so by Cubify Support. Any changes will alter the print quality of your creations.

Network

The 

Network

 menu allows the user to connect to a wireless network or to an ad hoc device.

System

SELECT LANGUAGE

 allows the user to localize the printer to their language.

LIGHT

 allows the user to turn on or off the print jet LEDs. The other interior LEDs are managed by the

firmware when the CubePro is powered on.

Advanced

Selecting the 

FIRMWARE

 icon allows the user to update their firmware either with a file downloaded to a

USB mass storage device or by wireless connection.

By selecting 

INFO

, the printer will display the printer status including the serial number, the print jet

Summary of Contents for CubePro 3D Printer















































































































Reviews:

No comments