manualshive.com logo in svg

3D Systems CubePro 3D Printer, User Manual, Page: 59 / 110

Share
Download
3D Systems CubePro 3D Printer User Manual Download Page 59

USING ADVANCED MATERIAL

Printing with advanced materials requires the purchase of both the advanced material upgrade and the
nozzle upgrade kit. After purchasing the advanced material upgrade, you will receive an 8-digit activation
code that will be required to activate the printer functionality. To print advanced materials, nozzle 2 must
be replaced with the special nozzle designed specifically for advanced materials.

CAUTION: Nozzles designed for standard materials should never be used to print

advanced materials.

Advanced materials include:

Wood

INF

FLEX

NOTE: Refer to the print jet replacement guide when installing the nozzle upgrade kit.

Activation

Select 

SETUP

 from the home screen.

1.

Select 

NOZZLE UPGRADE

.

2.

Go to 

www.3dsystems.com/shop

 and purchase the advanced material upgrade and upgrade kit.

3.

NOTE: Once you have purchased the upgrade and the nozzle upgrade kit, you will

receive a 8-digit activation code. Note the activation code because it will need to be

entered into the printer to activate your advanced material upgrade.

Once you have purchased the upgrade and the nozzle upgrade kit, select the 

checkmark

 to continue.

4.

Enter your 8-digit activation code and select the 

checkmark

 to continue.

5.

Summary of Contents for CubePro 3D Printer















































































































Reviews:

No comments