manualshive.com logo in svg

3D Systems CubePro 3D Printer, User Manual, Page: 51 / 110

Share
Download
3D Systems CubePro 3D Printer User Manual Download Page 51

NYLON MANUAL SUPPORTS

Using Nylon Manual Supports

When printing with nylon, parts with large, flat overhanging features may warp. CubePro software provides
readily-accessible nylon supports for your nylon-printed parts.

NOTE: The use of nylon manual supports requires INF support material to also be

installed in the printer and used as a support material type when setting the build

settings. INF support material is to be used in addition to the nylon supports you will

add to the part.

After loading your part to the print pad, select 

Open Manual Support

.

1.

Select the supports you will need by their height.

2.

NOTE: The height is noted by the variables after the last X in the file name. You may

have to keep trying different support sizes until you find the one that contacts the

bottom surface of the part needing support. 

NOTE: It is okay for the support to be taller than the bottom surface but the support

should not extrude above the part.

Add as many supports as you will need knowing that INF material will be printed around the supports providing additional stability.

3.

NOTE: For best results, place supports under the corners of overhanging features.

NOTE: Once you move the supports into position, adding additional manual supports

will reset all of them and each one will have to be repositioned.

Summary of Contents for CubePro 3D Printer















































































































Reviews:

No comments