manualshive.com logo in svg

3D Systems CubePro 3D Printer, User Manual, Page: 20 / 110

Share
Download
3D Systems CubePro 3D Printer User Manual Download Page 20

Cut off 2”/5 cm of print material from the end. Select the 

checkmark

 to continue.

14.

NOTE: Ensure the material is not bent or creased. If the material is not straight, pull

out the damaged material from the cartridge. Cut off and dispose the portion that is

not straight.

Insert the print material under the cartridge clamp roller of cartridge bay 1 and into the material tube. Select the 

checkmark

 to continue.

15.

Continue to manually feed the print material through the material tube until it begins to extrude from print jet 1 into the jet wiper assembly. Select the

16.

checkmark

 to continue.

NOTE: When the material reaches far enough into the extruder, the extruder motor

will assist with feeding the material further into the print jet.

(1) Push the front of the cartridge into place. (2) Then, push the cartridge handle downward until the cartridge is fully seated in its cartridge bay mount.

17.

Select the 

checkmark

 to continue.

NOTE: Ensure the front of the cartridge (A) where the material exits is seated under

the clamp roller and between the vertical alignment pins in the cartridge bay.

Summary of Contents for CubePro 3D Printer















































































































Reviews:

No comments