3D Systems CubePro 3D Printer User Manual Download Page 18

Page: 18 / 110

Select the

checkmark

to continue the warranty activation process.

www.3dsystems.com/shop/account/login

NOTE: You must be logged in to

www.3DSystems.com

to activate your printer. If you

have not activated an account, select

SIGN UP

or enter your information on the

signup page

Navigate to

http://3dsystems.com/shop/cubepro/activate

NOTE: The serial number of your printer will appear on the printer’s touchscreen

display. Take note of the serial number. You will need it to activate your printer. The

serial number can also be found on a label adhered to the right side of the printer

near the power on/oﬀ switch.
NOTE: This illustration provides an example of a serial number. Do not use this

number to activate your printer.

Select the

checkmark

to continue.

Enter your serial number and select

Activate

NOTE: Your 4-digit activation code will appear. Please note the activation code

because it will need to be entered into the printer’s touchscreen display to activate

the printer.
NOTE: You can access the User Guide, software for either Windows or Apple operating

systems, and free creations.

After receiving your activation code during the registration and warranty activation process, enter your 4-digit code in the touchscreen display. Select the

checkmark

to continue.

Summary of Contents for CubePro 3D Printer















































































































Search results

Summary of Contents for CubePro 3D Printer

Reviews:

3D Systems CubePro 3D Printer, User Manual, Page: 18 / 110

Search results

Summary of Contents for CubePro 3D Printer

Reviews: