manualshive.com logo in svg

3D Systems CubePro 3D Printer, User Manual, Page: 36 / 110

Share
Download
3D Systems CubePro 3D Printer User Manual Download Page 36

CUBEPRO SOFTWARE

CubePro software is an easy-to-use tool that simplifies the printing process. The software is available by
logging in to your 

http://3dsystems.com/shop

 account. Downloads are available for Windows and Mac

operating systems.

Installing Windows Software

Go to 

www.3dsystems.com/shop

 and log in with your username and password.

1.

Navigate to 

3dsystems.com/shop/cubepro/downloads

. Select 

Windows

 from the Software Download section at the bottom of the page. You can also

2.

download the software by clicking 

here

.

Run the installer file.

3.

Read through the End-User License Agreement. If you accept the terms of the agreement, select the acceptance checkbox and select 

Next

.

4.

NOTE: The software will begin to install.

Select 

Close

 once the software has been installed.

5.

Installing MAC Software

Go to 

www.3dsystems.com/shop

 and log in with your username and password.

1.

Navigate to 

3dsystems.com/shop/cubepro/downloads

. Select Mac from the Software Download section at the bottom of the webpage. You can also

2.

download the installer file by clicking 

here

.

Select the 

Downloads

 icon on the Dock and select the CubePro .dmg file.

3.

Drag the CubePro file into the Applications folder.

4.

Summary of Contents for CubePro 3D Printer















































































































Reviews:

No comments