ZyXEL Communications IES-1248-51 Скачать руководство пользователя | Manualshive

Страница: 40 / 385

background image

IES-1248-51 User’s Guide

40

Chapter 1 Getting to Know the IES-1248-51

MAC (Media Access Control) Count Filter

You can limit the number of MAC addresses that may be dynamically learned on a port. You
may enable/disable the MAC count filter on individual ports.

Static Multicast

Use static multicast to allow incoming frames based on multicast MAC address(es) that you
specify. This feature can be used in conjunction with IGMP snooping and IGMP proxy to
allow multicast MAC address(es) that are not learned by IGMP snooping or IGMP proxy.

IGMP Proxy

In a simple tree network, the system can proxy multicast traffic in order to improve network
performance.

IGMP Snooping

With IGMP snooping, group multicast traffic is only forwarded to ports that are members of
that group. IGMP Snooping generates no additional network traffic, allowing you to
significantly reduce multicast traffic passing through your IES-1248-51.

System Monitoring

• System status (link status, rates, statistics counters)
• Temperatures, voltage reports and alarms.

System Error Logging

The IES-1248-51’s system error log will record error logs locally. These logs may be viewed
again after a warm restart.

Alarm LED

An

ALM

(alarm) LED lights when the IES-1248-51 is overheated, the fans are not working

properly, the voltage readings are outside the tolerance levels or an alarm has been detected on
the ALARM input pins.

Bandwidth Control

The IES-1248-51 supports rate limiting in 32 Kbps increments allowing you to create different
service plans

Quality of Service

• Four priority queues for ENET and eight priority queues for downstream PVC so you can

ensure mission-critical data gets delivered on time.

• Follows the IEEE 802.1p priority setting standard.

«
...
38
39
40
41
42
...
»

Содержание IES-1248-51


































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IES-1248-51

Бренд: Sprint Страницы: 78

Бренд: Olive Страницы: 38

Бренд: Clear Страницы: 2

Бренд: Hama Страницы: 10

Бренд: Paradyne Страницы: 2

Бренд: 3Com Страницы: 56

QuickCarrier USB-D

Бренд: Multitech Страницы: 36

Бренд: US Robotics Страницы: 27

Бренд: tell Страницы: 11

Бренд: MikroTik Страницы: 9

Бренд: CSL Страницы: 16

Бренд: Ercogener Страницы: 51

Бренд: Ercogener Страницы: 69

Бренд: NETGEAR Страницы: 109

DG834v3 - ADSL Modem Router

Бренд: NETGEAR Страницы: 182

Бренд: Janus Remote Communications Страницы: 12

Бренд: Sierra Wireless Страницы: 15

Бренд: Zte Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды