ZyXEL Communications IES-1248-51 Скачать руководство пользователя

Страница: 81 / 385

IES-1248-51 User’s Guide

Chapter 9 Home and Port Statistics Screens

H A P T E R

Home and Port Statistics

Screens

This chapter describes the

Home

(status) and

Port Statistics

screens.

9.1 Home Screen

The

Home

screen of the web configurator displays a port statistical summary with links to

each port showing statistical details.

To open this screen, click

Home

in any web configurator screen.

Figure 41

Home

The following table describes the labels in this screen.

Table 5

Home

LABEL

DESCRIPTION

System up Time

This field shows how long the system has been running since the last time it was

started.

The following fields are related to the Ethernet ports.

ENET

This field displays the number of the Ethernet port. Click a port number to

display that port’s statistics screen. The

Ethernet Port Statistics Screen

appears.

See

Section 9.1.1 on page 82

Содержание IES-1248-51


































































































































































































































































































































































































Результаты поиска

Содержание IES-1248-51

Отзывы:

Похожие инструкции для IES-1248-51

Бренды по названию

Популярные бренды

ZyXEL Communications IES-1248-51, Руководство пользователя

Результаты поиска

Содержание IES-1248-51

Отзывы:

Похожие инструкции для IES-1248-51

Бренды по названию

Популярные бренды