ZyXEL Communications IES-1248-51 Скачать руководство пользователя страница 212

Страница: 212 / 385

IES-1248-51 User’s Guide

212

Chapter 34 Maintenance

Type the path and file name of the firmware file you wish to upload to the device in the

File

Path

text box or click

Browse

to locate it. After you have specified the file, click

Upgrade

34.3 Restore Configuration Screen

Use this screen to load a configuration file from your computer to the device.

To open this screen, click

Management

Maintenance

Click here

(Restore Text

Configuration).

Figure 111

Restore Configuration

Type the path and file name of the configuration file you wish to restore in the

File Path

text

box or click

Browse

to display a

Choose File

screen from which you can locate it. After you

have specified the file, click

Restore

. "conf-0" is the name of the configuration file on the

device, so your backup configuration file is automatically renamed when you restore using this
screen.

34.4 Backing Up a Configuration File

Backing up your device configurations allows you to create various “snap shots” of your
device from which you may restore at a later date.

Click

Management

Maintenance

, and do the following to save your device’s configuration

to your computer.

Right-click the

Click here

(Backup Text Configuration) link and click

Save Target

Or:

Click the

Click here

(Backup Text Configuration) link and then click

File

Save As

In the

Save As

screen, choose a location to save the file on your computer from the

Save

drop-down list box and type a descriptive name for it in the

File name

list box. Click

Save

to save the configuration file to your computer.

Note:

See chapters

to edit the configuration text file.

Содержание IES-1248-51


































































































































































































































































































































































































Результаты поиска

Содержание IES-1248-51

Отзывы:

Бренды по названию

Популярные бренды

ZyXEL Communications IES-1248-51, Руководство пользователя

Результаты поиска

Содержание IES-1248-51

Отзывы:

Бренды по названию

Популярные бренды