ZyXEL Communications IES-1248-51 Скачать руководство пользователя страница 213 | Manualshive

Страница: 213 / 385

ZyXEL Communications IES-1248-51 Скачать руководство пользователя страница 213

IES-1248-51 User’s Guide

Chapter 34 Maintenance

213

Note:

You can change the “.dat” file to a “.txt” file and still upload it back to the IES-
1248-51.

34.5 Load Factory Defaults

Use this function to clear all device configuration information you configured and return to the
factory defaults.

To do this, click

Management

,

Maintenance

,

Click here

(Restore Default Configuration).

Figure 112

Restore Default Configuration

Click

OK

to begin resetting all device configurations to the factory defaults and then wait for

the device to restart. This takes up to two minutes. If you want to access the device web
configurator again, you may need to change the IP address of your computer to be in the same
subnet as that of the default device IP address (192.168.1.1).

Figure 113

Restore Factory Default Settings, Reboot

34.6 Reboot System

Use this function to restart the device without physically turning the power off.

To open this screen, click

Management

,

Maintenance

,

Click here

(Reboot System).

«
...
211
212
213
214
215
...
»

Содержание IES-1248-51


































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды