ZyXEL Communications IES-1248-51 Скачать руководство пользователя | Manualshive

Страница: 314 / 385

background image

IES-1248-51 User’s Guide

314

Chapter 49 ADSL Commands

The hexadecimal digit is converted to binary and a '1' masks (disables) the corresponding tone.
Disabling a carrier tone turns it off so the system does not send data on it.

This command displays or sets masks for downstream carrier tones from 256 to 511 on the
specified ADSL2+ port(s). Use this command to have the system not use an ADSL line’s
tones that are known to have a high noise level.

The following example disables downstream carrier tone 307 for ADSL2+ port 5.

The following example disables downstream carrier tones 304 to 307 for ADSL2+ port 5.

The following example displays the results.

49.1.16 PMM Parameters Command

Syntax:

ras> param <portlist> [<l0time> <l2time> <l2atpr> <l2atprt>]
[<max_l2rate> <min_l2rate> <l0tol2_rate>]

<m4>

=

tones 384~415

<m5>

=

tones 416~447

<m6>

=

tones 448~479

<m7>

=

tones 480~511

Figure 200

ADSL Downstream Carrier1 Command Example 1

ras> adsl dscarrier1 5 0 00001000 0 0 0 0 0 0

Figure 201

ADSL Downstream Carrier1 Command Example 2

ras> adsl dscarrier1 5 0 0000f000 0 0 0 0 0 0

Figure 202

ADSL Downstream Carrier1 Command Display Example

ras> adsl dscarrier1 5
ds carrier
port m0 m1 m2 m3 m4 m5 m6 m7
---- |--------|--------|--------|--------|--------|--------|--------|-----
---|
5 00000000 000F0000 00000000 00000000 00000000 00000000 00000000
00000000
Tone:
m0:256-287, m1:288-319, m2:320-351, m3:352-383
m4:384-415, m5:416-447, m6:448-479, m7:480-511

«
...
312
313
314
315
316
...
»

Содержание IES-1248-51


































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IES-1248-51

Бренд: Kathrein Страницы: 16

Бренд: Kasda Страницы: 5

Бренд: Kasda Страницы: 6

DSL-2320B - 24 Mbps DSL Modem

Бренд: D-Link Страницы: 63

SocketModem MT2456SMI-22

Бренд: Multitech Страницы: 58

Бренд: SG Wireless Страницы: 6

Stick Atlas PXU1960

Бренд: Clear Страницы: 19

Бренд: ABB Страницы: 20

Бренд: Elcon Страницы: 24

Бренд: MikroTik Страницы: 8

Бренд: LOVATO ELECTRIC Страницы: 8

Бренд: Zte Страницы: 9

xComfort CKOZ-00/14

Бренд: Eaton Страницы: 2

Бренд: Ebyte Страницы: 20

Бренд: Ebyte Страницы: 29

Бренд: ICPDAS Страницы: 6

Бренд: Gigaset Страницы: 82

Бренд: NETGEAR Страницы: 292

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды