ZyXEL Communications IES-1248-51 Скачать руководство пользователя

Страница: 183 / 385

IES-1248-51 User’s Guide

Chapter 28 2684 Routed Mode

183

Figure 93

2684 Routed PVC

The following table describes the labels in this screen.

Table 45

2684 Routed PVC

LABEL

DESCRIPTION

Routed Domain

Click

Routed Domain

to open this screen where you can configure domains for

2684 routed mode traffic (see

Section 28.3 on page 184

RPVC ARP Proxy

Click

RPVC ARP Proxy

to go to the screen where you can view the Address

Resolution Protocol table of IP addresses of CPE devices using 2684 routed

mode and configure how long the device is to store them (see

Section 28.4 on

page 186

Routed Gateway

Click

Routed Gateway

to go to the screen where you can configure gateway

settings (see

Section 28.5 on page 186

Port

Use this drop-down list box to select a port for which you wish to configure

settings.

Gateway IP

Enter the IP address of the gateway to which you want to send the traffic that the

system receives from this PVC. Enter the IP address in dotted decimal notation.

VPI

Type the Virtual Path Identifier for this routed PVC.

VCI

Type the Virtual Circuit Identifier for this routed PVC. The IES-1248-51 uses this

PVC channel internally.

Enter the subscriber’s CPE WAN IP address in dotted decimal notation.

NetMask

The bit number of the subnet mask of the subscriber’s WAN IP address. To find

the bit number, convert the subnet mask to binary and add all of the 1’s together.

Take “255.255.255.0” for example. 255 converts to eight 1’s in binary. There are

three 255’s, so add three eights together and you get the bit number (24).
Make sure that the routed PVC’s subnet does not include the IES-1248-51’s IP

address.

DS VC Profile

Use the drop-down list box to select a VC profile to use for this channel’s

downstream traffic shaping.

US VC Profile

Use the drop-down list box to select a VC profile to use for this channel’s

upstream traffic. The IES-1248-51 does not perform upstream traffic policing if

you do not specify an upstream VC profile.

Add Click

Add

to save your changes to the IES-1248-51’s volatile memory.

The IES-1248-51 loses these changes if it is turned off or loses power, so use

the

Config Save

link on the navigation panel to save your changes to the non-

volatile memory when you are done configuring.

Cancel Click

Cancel

to start configuring the screen again.

Index

This field displays the number of the routed PVC.

Содержание IES-1248-51


































































































































































































































































































































































































Результаты поиска

Содержание IES-1248-51

Отзывы:

Похожие инструкции для IES-1248-51

Бренды по названию

Популярные бренды

ZyXEL Communications IES-1248-51, Руководство пользователя

Результаты поиска

Содержание IES-1248-51

Отзывы:

Похожие инструкции для IES-1248-51

Бренды по названию

Популярные бренды