ZyXEL Communications IES-1248-51 Скачать руководство пользователя | Manualshive

Страница: 184 / 385

background image

IES-1248-51 User’s Guide

184

Chapter 28 2684 Routed Mode

28.3 2684 Routed Domain Screen

Use this screen to configure domains for 2684 routed mode traffic. The domain is the range of
IP addresses behind the subscriber’s device (the CPE). This includes the CPE device’s LAN IP
addresses and the IP addresses of the LAN computers.

To open this screen, click

Advanced Application

,

2684 Routed Mode

,

Routed Domain

.

Figure 94

2684 Routed Domain

Port

This field displays the number of the ADSL port on which the routed PVC is

configured.

VPI

This field displays the Virtual Path Identifier (VPI) The VPI and VCI identify a

channel on this port.

VCI

This field displays the Virtual Circuit Identifier (VCI). The VPI and VCI identify a

channel on this port.

IP

This field displays the subscriber’s IP address.

DS / US VC Profile

This shows which VC profile this channel uses for downstream traffic shaping.

The VC profile for upstream policing also displays if the channel is configured to

use one.

NetMask

This field displays the bit number of the subnet mask of the subscriber’s IP

address.

Gateway IP

This field displays the IP address of the gateway to which you want to send the

traffic that the system receives from this PVC.

Delete

Select an entry’s

Delete

check box and click

Delete

to remove the entry.

Clicking

Delete

saves your changes to the IES-1248-51’s volatile memory.

The IES-1248-51 loses these changes if it is turned off or loses power, so use

the

Config Save

link on the navigation panel to save your changes to the non-

volatile memory when you are done configuring.

Cancel Click

Cancel

to start configuring the screen again.

Table 45

2684 Routed PVC (continued)

LABEL

DESCRIPTION

«
...
182
183
184
185
186
...
»

Содержание IES-1248-51


































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IES-1248-51

Бренд: E-Lins Страницы: 4

Бренд: Skypatrol Страницы: 33

Бренд: CalAmp Страницы: 62

Бренд: Zte Страницы: 25

Бренд: Myzone Страницы: 4

Бренд: Ebyte Страницы: 34

Бренд: 3Com Страницы: 101

Бренд: 3Com Страницы: 115

Бренд: B+B SmartWorx Страницы: 2

Cerberus P 6311-072

Бренд: Pentagram Страницы: 54

Бренд: Ubee Страницы: 34

Бренд: Hughes Страницы: 66

Бренд: Hughes Страницы: 126

Бренд: Hughes Страницы: 140

Бренд: Zte Страницы: 24

Бренд: Campbell Страницы: 56

Бренд: Radyne Страницы: 201

Бренд: Quatech Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды