manualshive.com logo in svg

ZyXEL Communications IES-1248-51, Руководство пользователя

Поделиться
Скачать
ZyXEL Communications IES-1248-51 Скачать руководство пользователя страница 195

IES-1248-51 User’s Guide

Chapter 31 Access Control

195

31.3.1  Supported MIBs

MIBs let administrators collect statistics and monitor status and performance. The IES-1248-
51 supports the following MIBs:

• MIB II IF MIB and ADSL line MIB (RFC-2662)
• SNMP MIB II (RFC-1215)
• BRIDGE MIB: FDB status

The IES-1248-51 can also respond with specific data from the DSLAM private MIBs:

• dslam.mib
• dslam-AS-ATM.mib
• dslam-AS.mib
• dslam-AESCommon.mib
• dslam-iesCommon.mib
• ies1248.mib

31.3.2  SNMP Traps

The IES-1248-51 can send the following SNMP traps to an SNMP manager when an event 
occurs. ATUC refers to the downstream channel (for traffic going from the IES-1248-51 to the 
subscriber). ATUR refers to the upstream channel (for traffic coming from the subscriber to 
the IES-1248-51).

Set

 Allows the manager to set values for object variables within an agent. 

Trap

 Used by the agent to inform the manager of some events.

Table 52   

SNMP Commands (continued)

COMMAND

 DESCRIPTION

Table 53   

SNMPv2 Traps

TRAP NAME

DESCRIPTION

coldStart

This trap is sent when the IES-1248-51 is turned on.

warmStart

This trap is sent when the IES-1248-51 restarts.

linkDown

This trap is sent when the Ethernet link is down. Enterprise specific 

(adsl_atuc_los) traps are sent when an ADSL link is down.

linkUp

This trap is sent when the Ethernet or ADSL link comes up.

authenticationFailure

This trap is sent when the SNMP community check fails.

reboot

This trap is sent when the system is going to reboot. The variable is the 

reason for the system reboot.

overheat

This trap is sent when the system is overheated. The variable is the 

current system temperature in Celsius.

Содержание IES-1248-51


































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды