ZyXEL Communications IES-1000 - ANNEXE 7 Скачать руководство пользователя страница 62

Страница: 62 / 139

NetAtlas IES-1000 (AAM1008) EMS User’s Guide

7-4

The Configuration Menus

Figure 7-3 Configuration: ADSL Line: Profile Setup

The following table describes the labels in this screen.

Table 7-2 Configuration: ADSL Line: Profile Setup

LABEL DESCRIPTION

All Profiles

This field lists the profile names for all profiles configured.

DEFVAL

is the default profile.

Channel Mode

This field displays the ADSL latency mode for the ports that belong to this profile.

fast

mode uses no interleaving and provides faster transmission (a “fast channel”). This

would be suitable if you have a good line where little error correction is necessary.

interleave

mode uses interleave delay when transmission error correction (Reed-

Solomon) is necessary due to a less than ideal telephone line.

Interleave Delay

This field displays the number of milliseconds (1-255) of interleave delay to use for
upstream/downstream transfers.

Upstream (ATU-R)

Downstream (ATU-C)

ATU-R (ADSL Termination Unit-Remote) refers to the channel for traffic coming to the IES
from the subscriber (upstream).

ATU-C (ADSL Termination Unit-Central) refers to the channel for traffic going from the IES
to the subscriber (downstream).

Min Tx Rate This field displays the minimum transmission speed in kilobits per second (Kbps).

Max Tx Rate This field displays the maximum transmission speed in kilobits per second (Kbps).

Содержание IES-1000 - ANNEXE 7












































































































































Результаты поиска

Содержание IES-1000 - ANNEXE 7

Отзывы:

ZyXEL Communications IES-1000 - ANNEXE 7, Руководство пользователя, Страница: 62 / 139

Результаты поиска

Содержание IES-1000 - ANNEXE 7

Отзывы: