manualshive.com logo in svg

Zyno Medical Z-800, Инструкция по эксплуатации, Страница: 50 / 69

Поделиться
Скачать
Zyno Medical Z-800 Скачать руководство пользователя страница 50

 

Z-800 Instructions for Use. 

 

50/69 

P/N 800-600-01-08 Rev 08/10

 

 

MAINTENANCE 

 

CONFIGURABLE SETTINGS 

 

Adjusting the Occlusion Pressure Threshold 

 
Pressure Sensor detects down-stream occlusion in the 
IV sets. User may specify occlusion alarm pressure 
threshold in configuration screen. The occlusion alarm 
threshold can be adjusted between 4 psi and 30 psi 
 

1.

 

From the configuration menu, Select 

8. 

BIOMED OPT

.  

 

2.

 

In the BIOMED OPTION menu, Select

 8.1. 

PRESSURE

.  

 

3.

 

In the Pressure sub-menu, use 

Up/Down Arrow

 

to adjust the occlusion alarm pressure threshold.  

 

4.

 

Press 

OK

 soft key 

 to confirm the set value. 

Press 

QUIT

 soft key  

 to back out of 

PRESSURE sub menu. Press 

QUIT

 soft key  

 

again to exit the BIOMED OPTION menu 

 
 
 
 
 
 
 
 
 
 
 

  WARNING:  

The factory default settings 

should be used unless qualified clinical personnel 
determine that other customized settings are 
appropriate and safe. 

 

 

 

 

 

 

 

Содержание Z-800






































































Отзывы:

Нет отзывов