Zyno Medical Z-800 Скачать руководство пользователя страница 30

Страница: 30 / 69

Z-800 Instructions for Use.

30/69

P/N 800-600-01-08 Rev 08/10

GETTING STARTED

TPN MODE INFUSION (Continued)

Programming TPN Mode Infusion

TPN infusion programming screen contains the following
display areas:
1.

Status Bar

: The Status Bar displays current operating

mode; current pump state; and volume infused.



TPN

: TPN mode operation.



SET

: Pump programming state.



VINF

: Volume Infused for the current infusion.

Infusion Parameters

: TPN total VTBI and Total TIME

of the infusion.



TIME

: Total TIME of the infusion.



VTBI

: Total Volume To Be Infused.

Soft Keys

: Allow user to access pump configuration and

TPN ramp programming screen.



CONFIG

: Access pump configuration.



RAMP

: Access TPN Ramp Up and Ramp Down

Time parameter programming.



Up/Down Arrows

: Highlight the selected parameter

item.

WARNING: Do not over-program VTBI. Program

the actual amount of the fluid in the IV bag.

The TPN infusion parameters may be programmed by using
the UP/DOWN Arrow keys and Data Entry keys.

Access TPN Ramp Time Parameter Programming

From TPN programming screen, press RAMP Soft-Key to
access TPN Ramp Parameter programming screen.

Programming TPN Ramp Time Parameters

The TPN Ramp Time parameters may be programmed by
using the UP/DOWN Arrow keys and Data Entry keys.

Содержание Z-800






































































Результаты поиска

Содержание Z-800

Отзывы:

Zyno Medical Z-800, Инструкция по эксплуатации, Страница: 30 / 69

Результаты поиска

Содержание Z-800

Отзывы: