manualshive.com logo in svg

Zyno Medical Z-800, Инструкция по эксплуатации, Страница: 20 / 69

Поделиться
Скачать
Zyno Medical Z-800 Скачать руководство пользователя страница 20

 

Z-800 Instructions for Use. 

 

20/69 

P/N 800-600-01-08 Rev 08/10

 

 

GETTING STARTED 

 

CONTINUOUS MODE--SECONDARY INFUSION 

 

Access Secondary Infusion Programming Screen 

 

From the Continuous Mode Primary Infusion 
Programming screen, Press SEC soft key to access the 
secondary infusion programming screen.   

 

 

Secondary Infusion Programming Screen 

 
Similar to the primary infusion programming screen, The 
secondary infusion programming screen contains the 
following display areas: 
1.

 

Status Bar

:  The Status Bar displays current 

operating mode; current pump state; and volume 
infused. 

 

CONT

:  Continuous Mode Operation. 

 

SET

:  Setup pump state. 

 

VINF

:  Volume Infused for the current 

infusion. 

2.

 

Infusion Parameters

:  Secondary Flow Rate and 

Secondary Volume To Be Infused. 

 

Sec RATE

:  Secondary Flow Rate. 

 

Sec VTBI

:  Secondary VTBI. 

 

3.

 

Soft Keys

:  Allow user to access pump configuration 

and primary infusion programming screen. 

 

CONFIG

:  Access pump configuration.  

 

PRI

:  Access primary infusion programming. 

 

Up/Down Arrows

: Select parameter items. 

 

 

 

 

 

 

Содержание Z-800






































































Отзывы:

Нет отзывов