Zyno Medical Z-800 Скачать руководство пользователя страница 25

Страница: 25 / 69

Z-800 Instructions for Use.

25/69

P/N 800-600-01-08 Rev 08/10

GETTING STARTED

TIME/VOLUME Programming (Continued)

Programming in TIME/VTBI Option

Upon selection of the TIME/VTBI programming option,
the continuous mode infusion programming screen will
present Total Infusion Time and Total VTBI parameters.
The TIME/VTBI infusion programming screen contains
the following display areas:

Status Bar

: The Status Bar displays current operating

mode; current pump state; and volume infused.



CONT

: Continuous Mode Operation



SET

: Programming pump state.



VINF

: Volume Infused for the current infusion.

Infusion Parameters

: -- Primary Infusion Time and

Primary Volume To Be Infused.



Pri TIME

: Primary Infusion Time.



Pri VTBI

: Primary VTBI.

Soft Keys

: Allows user to access pump configuration

and secondary infusion programming screen.



CONFIG

: Access pump configuration.



SEC

: Access secondary infusion programming

screen. The Secondary Infusion Parameters will be
presented as Sec TIME and Sec VTBI



Up/Down Arrows

: Select parameter items. Similar

to the RATE/VTBI programming screen, The
TIME/VTBI infusion parameters may be
programmed by using the UP/DOWN Arrow keys
and Data Entry keys.

WARNING: Do not over-program VTBI.

Program the actual amount of the fluid in the IV bag.

Содержание Z-800






































































Результаты поиска

Содержание Z-800

Отзывы:

Zyno Medical Z-800, Инструкция по эксплуатации, Страница: 25 / 69

Результаты поиска

Содержание Z-800

Отзывы: