manualshive.com logo in svg

Zyno Medical Z-800, Инструкция по эксплуатации, Страница: 12 / 69

Поделиться
Скачать
Zyno Medical Z-800 Скачать руководство пользователя страница 12

 

Z-800 Instructions for Use. 

 

12/69 

P/N 800-600-01-08 Rev 08/10

 

 

GETTING STARTED 

 

INSTALLATION PROCEDURE 

 

UNPACK THE PUMP 

The Z-800 infusion pump is supplied complete with 

 

A standard detachable, listed/certified IEC Hospital 
Grade electrical cord. 

 

Pole Clamp pre-mounted at 45 degree angle to the 
pump. 

 

Instruction for Use. 

 

1.

 

Remove Pump module from its carton. 

2.

 

Inspect the pump. 

3.

 

Check to ensure pump door operates freely.  

4.

 

Check for any loose parts. 

 

NOTE:

  If any of the following conditions are observed, 

the Z-800 pump must be removed from use and inspected 
by qualified personnel: 

 

Look for any signs of physical damage from 
shipping.  

 

LED segments are not illuminated during system 
power-on self-test. 

 

Indicator lights do not illuminate. 

 

Audio tune does not sound. 

 

Main Display does not appear backlit, appears 
irregular, or has evidence of a row of pixels not 
functioning properly. 
 
 

 

 
 

MOUNT PUMP TO IV POLE 

1.

 

Attach the pump to an IV pole by turning the knob on 
the pole clamp clockwise, or place the pump on a flat, 
stable surface. 

 

 

Содержание Z-800






































































Отзывы:

Нет отзывов