Zyno Medical Z-800 Скачать руководство пользователя страница 32

Страница: 32 / 69

Z-800 Instructions for Use.

32/69

P/N 800-600-01-08 Rev 08/10

GETTING STARTED

INTERMITTENT MODE INFUSION (Continued)

Programming INTERMITTENT Mode Infusion

INTERMITTENT infusion programming screen contains the
following display areas:
5.

Status Bar

: The Status Bar displays current operating

mode; current pump state; and volume infused.



INTR

: INTERMITTENT mode operation.



PROG

: Pump programming state.



VINF

: Volume Infused for the current infusion.

Infusion Parameters

: INTERMITTENT total VTBI and

Cycle TIME of the infusion.



Total VTBI

: Total Volume To Be Infused.



Cycle Time

: Time for each cycle (Hour

Minute

format. Cycle time should be programmed between 30
minutes and 24 hours. If programmed Cycle Time is
outside the range, pump alarms ―Invalid Parameters‖).

Soft Keys

: Allow user to access pump configuration and

INTERMITTENT ramp programming screen.



CONFIG

: Access pump configuration.



PERIOD

: Access INTERMITTENT period

parameter programming.



Up/Down Arrows

: Highlight the selected parameter

item.

The Total VTBI and Cycle Time parameters may be
programmed by using the UP/DOWN Arrow keys and Data
Entry keys.

Note:

During idle period, pump runs at KVO rate. Volume

infused during idle period is counted. Pump alarms ―Infusion
Completed‖ once VINF (volume infused) equals programmed
Total VTBI.

Содержание Z-800






































































Результаты поиска

Содержание Z-800

Отзывы:

Zyno Medical Z-800, Инструкция по эксплуатации, Страница: 32 / 69

Результаты поиска

Содержание Z-800

Отзывы: