Zurich ZR13s, Руководство пользователя

Страница: 8 / 52

For technical questions, please call 1-888-866-5797
6
About the Scan Tool
DIS PL AY FUNC TIONS
3
5. M (Menu) button – W hen pre sse d, d isp lay s th e M ain Men u.
6. LD button – When pressed while linked to a vehicle, places the
Scan To ol in Live Data mode.
7. UP butto n – When in ME NU mode, scrolls UP through the
menu optio ns. When LINKED to a vehic le, scrolls UP thro ugh the
current disp lay screen to disp lay any addit iona l data.
8. ENTER button
- When in Menu mode, confirms the selected
option or value.
9. DOWN button - W hen in M EN U m ode , s cro lls do wn thr oug h the
menu options. When LI NKED to a veh icl e, scr olls do wn throu gh the
current disp lay screen to disp lay any addit iona l data.
10.GR EEN L ED - Indicates tha t all eng ine s ystems are runnin g
normally (all Monitors on the vehi cle are a ctive and performing their
diagnostic testing, and no DTCs are present).
11.YEL LOW LE D - Indicates there is a possible problem. A “Pe nding”
DTC is pres ent and/or some of the vehicle's em ission mon itors have
not run their dia gnostic testin g.
12.RE D L ED - Indicates there is a problem in one or more o f th e
vehicle's system s. The red LED is al so used to show that DT C(s)
are present. DTCs are show n on the Scan Tool’s LCD display. In
this case, the Malfunctio n Indicator (“Check Eng ine”) lamp on the
vehicle 's ins tru men t p ane l will light steady on.
13.Di splay
- D isp lay s te st r esu lts , S can T ool fun ctio ns and Mon ito r s tat us
info rm atio n. S ee DIS PLA Y F UN CT IO NS , b elo w, fo r d eta ils .
14.CABLE - C onn ect s th e S can Too l to the ve hic le' s D ata Li nk C onn ect or
(DLC).
DISPLAY FUNC TIONS
Figure 2. Display Functions
See F igure 2 for the locations of items 1 through 15, below.
1. I/M M ONIT OR S TA TU S f ield - Id ent ifie s th e I/ M Monitor status area.
4
3
2
5
7
6
1 14
10
11
12
8
9
13
15
CODE RETRIEVAL PROCEDURE
Using the Scan Tool
CODE RETRIEVAL PROCEDURE
6
Retrieving and using Diagnostic Trouble Codes (DTCs) for
troubleshooting vehicle operation is only one part of an
overall diagnostic strategy.
CODE RETRIEVAL PROCEDURE
Never replace a part based only on the DTC definition.
Each DTC has a set of testing procedures, instructions and
flow charts that must be followed to confirm the location of
the problem. Always refer to the vehicle's service manual
for detailed testing instructions.
Check your vehicle thoroughly before performing
any test.
ALWAYS observe safety precautions whenever working on a
vehicle.
1. Turn the ignition off.
2. Locate the vehicle's 16-pin Data Link
Connector (DLC).
Some DLCs have a plastic cover
that must be removed before
connecting the Scan Tool cable
connector.
If the Scan Tool is ON, turn it OFF
BEFORE connecting the Scan
Tool to the DLC.
3. Connect the Scan Tool to the vehicle’s
DLC. The cable connector is keyed and
will only fit one way.
„
If you have problems connecting the cable connector to the DLC,
rotate the connector 180°.
„
If you still have problems, check the DLC on the vehicle and on
the Scan Tool.
4. Turn the ignition on. DO NOT start the engine.
5. When the Scan Tool is properly connected to the vehicle’s DLC, the
unit automatically turns ON.
„
If the unit does not power on automatically, it may indicate there
is no power present at the vehicle’s DLC connector. Check the
fuse panel and replace any burned-out fuses.
„
If replacing the fuse(s) does not correct the problem, consult your
vehicle’s repair manual to identify the proper computer (PCM)
fuse/circuit, and perform any necessary repairs before proceeding.