Zurich ZR13s, Руководство пользователя

Страница: 25 / 52

For technical questions, please call 1-888-866-5797
23
About the Scan Tool
DISPLAY FUNCTIONS
3
5. M (Menu) button – When pressed, displays the Main Menu.
6. LD button – When pressed while linked to a vehicle, places the
Scan Tool in Live Data mode.
7. UP button – When in MENU mode, scrolls UP through the
menu options. When LINKED to a vehicle, scrolls UP through the
current display screen to display any additional data.
8. ENTER button
- When in Menu mode, confirms the selected
option or value.
9. DOWN button - When in MENU mode, scrolls down through the
menu options. When LINKED to a vehicle, scrolls down through the
current display screen to display any additional data.
10. GREEN LED - Indicates that all engine systems are running
normally (all Monitors on the vehicle are active and performing their
diagnostic testing, and no DTCs are present).
11. YELLOW LED - Indicates there is a possible problem. A “Pending”
DTC is present and/or some of the vehicle's emission monitors have
not run their diagnostic testing.
12. RED LED - Indicates there is a problem in one or more of the
vehicle's systems. The red LED is also used to show that DTC(s)
are present. DTCs are shown on the Scan Tool’s LCD display. In
this case, the Malfunction Indicator (“Check Engine”) lamp on the
vehicle's instrument panel will light steady on.
13. Display
- Displays test results, Scan Tool functions and Monitor status
information. See DISPLAY FUNCTIONS, below, for details.
14. CABLE - Connects the Scan Tool to the vehicle's Data Link Connector
(DLC).
DISPLAY FUNCTIONS
Figure 2. Display Functions
See Figure 2 for the locations of items 1 through 15, below.
1. I/M MONITOR STATUS field - Identifies the I/M Monitor status area.
4
3
2
5
7
6
1 14
10
11
12
8
9
13
15
VIEWING LIVE DATA
Live Data Mode
VIEWING LIVE DATA
23
The Scan Tool lets you view and/or "capture" (record) "real-time" Live
Data. This information includes values (volts, rpm, temperature, speed
etc.) and system status information (open loop, closed loop, fuel system
status, etc.) generated by the various vehicle sensors, switches and
actuators. These are the same signal values generated by the sensors,
actuators, switches and/or vehicle system status information used by
the vehicle's computer when calculating and conducting system
adjustments and corrections.
The real time (Live Data) vehicle operating information (values/status)
that the computer supplies to the Scan Tool for each sensor, actuator,
switch, etc. is called Parameter Identification (PID) Data.
Each PID (sensor, actuator switch, status, etc.) has a set of operating
characteristics and features (parameters) that serve to identify it. The
Scan Tool displays this information for each sensor, actuator, switch or
status that is supported by the vehicle under test.
WARNING : If the vehicle must be driven in order to perform a
troubleshooting procedure, ALWAYS have a second person
help you. One person should drive the vehicle while the other
person observes the Scan Tool data. Trying to drive and
operate the Scan Tool at the same time is dangerous, and
could cause a serious traffic accident.
VIEWING LIVE DATA
5. While linked to the vehicle, start the engine, then press LD .
6. A “One moment please . . .” message displays while the Scan Tool
establishes communication with the vehicle.
„
If the Scan Tool fails to establish communication with the vehicle,
a “Communication Error” message displays.
- Ensure your vehicle is OBD2
compliant.
- Verify the connection at the DLC,
and verify the ignition is ON.
- Turn the ignition OFF, wait 5
seconds, then back ON to reset
the computer.
- Press ENTER to continue.
7. Real-time Live Data (PID) information supported by the vehicle
under test displays.
„
If Live Data is not supported by the vehicle under test, an
advisory message displays. Press
SYSTEM MENU to return
to the System Menu. Live Data is not available for your vehicle.
The values for the various PIDS displayed may change as the
vehicle's operating conditions change.
8. Only a limited amount of PID data can be displayed on the screen at
one time. If additional PID data is available, a small arrow is shown
on the display. Press
UP and DOWN , as necessary, to view
all available PID data.