7
、
FRONT FORK COMPONENT
65
CHK
ADJ
NO.
PART NO.
PART NAME
QTY
CAUTION
1
1154200-023000 ZT310
-
VX Throttle Refueling
1
2
1154200-022000 ZT310
-
VX Throttle Return Line
1
3
1224100-030000 Pin tie (Black 4.8×130
)
1
4
1224100-051000 0 Flame retardant tie (black 2.5×100)
1
5
1244100-042000 ZT250
-
R Right handlebar rubber sleeve
1
6
1184200-185000
ZT310
-
V1 Right handlebar switch
1
7
1250205-031091 GB70.1M6×30 (stainless steel)
2
10N.m
8
1184200-147000 ZT310-R Second-generation right hand switch (TFT)
1
PROCEDURE:
●
Disassemble the throttle line
Use a 10# open-end wrench to turn the nut
②
of the throttle fuel line
⑴
or return line
⑵
up to the end, turn the nut
④
downwards out of the adjusting pipe
①
;
;
rotate the turntable on the throttle valve clockwise, and turn the cylindrical joint
of the fuel line from the turntable Remove; then move the adjustment tube upwards over the bracket
③
on the throttle valve
and pull outwards to separate the core from the bracket.Similarly, remove the oil return line.
Pass the throttle line out of the slot of the plug strap
⑶
and do not cut the strap
⑶
. Find the cable tie
⑷
on the right side
of the body and cut it.
Using 5# inner hexagon socket loosen the bolts
⑺
; remove the sub switch
⑻
and the right brake rocker arm assembly
⑧
in the direction of the arrow and lock the bolt
⑺
.Always keep disc brake main pump
⑧
high.
Hold the right hand switch
⑹
with your hand,Use 5# inner hexagon to remove bolts
⑥
and
⑦
, and then remove bolt
⑨
that comes with the switch. Switch the upper and lower parts of the switch.
Remove the throttle cable from the right hand and remove the rubber sleeve
⑸
from the core turntable
⑩
, and then
remove it from the cable hole in the lower part of the switch.
●
Install the throttle line
First pass the throttle cable into the cable hole in the lower part of the switch. Fit the cylindrical connector of the throttle
cable into the turntable
⑩
on the right hand gripper . Return the oil return line card to the limit slot provided on the fuel
line.Tighten the bolt
⑥
with a 5# inner hexagon tool, the torque is 8
~
10N.m. The switch mounting hole is slightly twisted
a few times for the rear bolt
⑦
and the bolt
⑨
is locked after observing the positioning hole and the direction of the lower
part of the switch
⑹
.Finally, tighten the bolt
⑦
and tie the tie
⑷
. Cut off the excess. Reset the sub switch and rocker
assembly and note the symbol on the alignment switch.
Install the throttle cable into the slot of the hub clamp
⑶
.
Turn the nut
②
of the throttle refueling line
⑴
or the return line
⑵
up to the end, and turn the nut
④
downwards to the
adjustment pipe
①
.
Put the oil return line into the bracket
③
, and fit the connector into the turntable
⑤
.
Put the oil line into the bracket
③
, then turn the turntable
⑤
to a certain angle, and then insert the connector.
Refer to the method of adjusting the gap to adjust the throttle line clearance; after adjusting the left and right direction of
rotation, there should be no change in idle speed and flexible reset.
Lock nuts
②
and
④
.
Fig.4 FRONT FORK
COMPONENT
Replace the throttle line
Содержание ZT310-V1 EURO V
Страница 1: ...2021 1 13 Service manual ZT310 V1 EURO V ...