![background image](http://html1.mh-extra.com/html/zodiac/noosa-reef/noosa-reef_instruction-manual_3981292055.webp)
SKIMMER BOX INSTALLATION
53
SILICONE SEALANT REQUIRED (NOT SUPPLIED)
Important notice:
Do not use the silicone sealants that are designed for use with windows and glass as they have an acidic cure
and can damage vinyl and some plastics. If the sealant smells like vinegar do not use it for this application.
A. Insert the double layer gasket around the cut out in the pool walll that there is a gasket layer on each side of the pool wall and
the screw holes line up (DO NOT UNDER ANY CIRCUMSTANCES CUT THE GASKET.)
B. Silicone sealer should now be applied to the back of the face plate, the front of the weir skimmer box, and to both sides of the
single rubber gasket in a single bead of approximately 5mm to assist in forming a leak proof seal between the liner and the
pool wall.
C. Use the screws supplied to locate the 4 corner screw holes of the skimmer box. Please make sure that the pool water depth is
at least 60cm before fitting the skimmer box as the liners can be under very high tension in the initial stages of filling the pool and
skimmer installation at this time can damage the liner.The four (4) corner screws are fitted from inside the pool, through the face
plate, single gasket double gasket and the pool wall, through into the skimmer box. Initially tighten screws 3 to four turns only.
D. With the four corner screws holding the skimmer box in place begin screwing in the upper and lower centre screws so that the
face plate starts to bend into a similar shape to the pool wall (do not over tighten screw.)continue fixing the screws from the upper
and lower centre position outward, as indicated by the numbering sequence below.
Tighten the four corner screws first once all others are in place.
E. Continue to fasten screws until all screws are tight, being careful not to over tighten the screws. Higher voltage cordless drills can
strip the thread in the skimmer box. Upon tightening a small amount of silicone sealant may be extruded from between the face
plate and the pool liner, this should be wiped with a rag as to remove any unsightly excess. Allow the recommended cure time
for the sealant before immersing in water.
F. The opening for the skimmer box can now be cut into the liner. It is important that this area be checked for leaks periodically.
(You can now cut the opening in the liner.)
G. Congratulations.The assembly/installation of your pool is now complete.You may now install the filtration motor/pump as per the
equipment suppliers instructions.
H. Operating instructions
1.To adjust inlet flow direction loosen knurled outer ring of eyeball fitting, move ball to desired position and tighten knurled ring
hand tight..
2.To clean basket, only remove skimmer cover and pull it out.
3. To attach vacuum cleaner hose, remove top cover. Put the vacuum adapter into the skimmer fill hose with water and insert
vacuum hose to the vac adapter.
1st
6th
3rd
2
n
d
4th
5th
8th
7th
5th
4th
2
n
d
3rd
6th
8th
7th
1st
1st
1st
Ski
mm
er Box
Ski
mm
er Face Plate
Ski
mm
er Box
Ski
mm
er Face Plate
Pool Wall
Pool Wall
1. Face plate positio
n
with 4 cor
n
er
locati
ng
screws i
n
place
2. Face plate positio
n
with ce
n
tre
screw al
m
ost co
m
pletely
f
aste
n
ed
Содержание NOOSA REEF
