Zero88 FROG 2 Скачать руководство пользователя страница 128

Страница: 128 / 184

User Definable Faders

Page 128

Frog 2 Operating Manual – Issue 4.3

Flash Mode

If the Flash Mode is set to

Flash

- the corresponding data assigned to the UDF is output

instantly on pressing the UDF flash button and faded out or released instantly on releasing
the UDF flash button.

If the Flash Mode is set to

Latch

- The first press is equivalent to raising the fader from

zero to full. The second press is equivalent to lowering the fader from full to zero.
Subsequent button presses then toggle between the two states.

The LED in the flash button indicates the state of the button (on or off). When the outputs
are fading up or down, the LED in the button flashes.

A Cue assigned to a UDF uses the fade times programmed in the cue data. The times for
the cue data can be displayed and edited as required via the

Preview UDF Window

or by

loading the UDF into the

Program Window

. Note – if you edit the fade times for the cue,

this will also affect the output of the cue in the relevant cue stack on the playbacks.

Channel Data assigned to a UDF uses the fade times programmed with the channel data
in the

Program Window

. The times for the channel data can be displayed and edited as

required via the

Preview UDF Window

or by loading the UDF into the

Program Window

Trigger Level

The Trigger Level applies to the Colour, Beam, Position and Effects parameters that are
programmed in the channel data or cue assigned to the UDF.

Each assigned UDF with Channel Data or Cue Data will have it’s own trigger level defined
(0 – 100% if percentage or 0 – 255 if DMX).

The initial trigger level is defined as the position of the physical fader when the flash button
is pressed to assign the channel data or cue to the UDF. The trigger level may be adjusted
as required via the

UDF Setup Window.

Содержание FROG 2

























































































































































































Результаты поиска

Содержание FROG 2

Отзывы:

Похожие инструкции для FROG 2

Бренды по названию

Популярные бренды

Zero88 FROG 2, Руководство по эксплуатации

Результаты поиска

Содержание FROG 2

Отзывы:

Похожие инструкции для FROG 2

Бренды по названию

Популярные бренды