Zeppelin 1x8 Cabinet Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 52

background image

31

7. Use the hammer to tap the four t-nuts (Part # NU03) into the four holes near the round cutout. Keep

tapping until the t-nuts are flat against the board.

96

8. Paint the side of the baffle board with the t-nuts and the inside surface of the round cutout flat

black. No other sides need to be painted.

97

Allow to dry thoroughly! Go work on the cabinet

while you are waiting.

9. Now it is time to put on the grill cloth. Attaching grill cloth in a way that looks nice is not an easy

task. There are two goals to keep in mind in working with grill cloth: 1) keep the lines straight;
and 2) make the grill cloth tight. There are several different techniques for accomplishing these
two goals, but the process described here has worked well for us. If you aren’t confident about
doing this step, call your local upholstery shop and they might be able to help you out.

The first part of putting on grill cloth consists of folding the four sides while carefully following straight
lines.

96

97

«
...
29
30
31
32
33
...
»

Содержание 1x8 Cabinet





















































Отзывы:

Нет отзывов

Похожие инструкции для 1x8 Cabinet

Бренд: Jam Audio Страницы: 6

Бренд: JBL Страницы: 2

Бренд: Cambridge Audio Страницы: 2

Бренд: QSC Страницы: 10

Бренд: JBL Страницы: 8

Бренд: Omnitronic Страницы: 39

Бренд: Dynacord Страницы: 2

SOUND STATION FOR PSP SLIM

Бренд: GAMERON Страницы: 40

Бренд: Turbosound Страницы: 13

Бренд: Konix Страницы: 8

HyperSpike TCPA-Omni

Бренд: Ultra electronics Страницы: 12

Бренд: Artsound Страницы: 4

Longhorn 21202124

Бренд: oklahoma joes Страницы: 36

CYBERBLUE POWER TUBE MagStation

Бренд: MiPow Страницы: 4

Spacia CI-MM3-II

Бренд: Phase Technology Страницы: 4

Бренд: Kaption Audio Страницы: 12

JBL NightLife Series

Бренд: Harman Страницы: 12

Бренд: XINJI Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды