Zelmer ZCM4821B, Руководство пользователя

Страница: 30 / 44

30
ZCM4821-001_v01
CHANGING AND STORING THE CUP FILLING LEVEL IN BEAN MODE
The coffee machine is set for standard quantities by default. However, you can set the cup
filling level individually for each cup size. Proceed as follows:
●
Press the button C repeatedly until the required cup symbol for the desired ground
coffee quantity is displayed.
The cup filling level for one cup is stored during this process.
●
lace an appropriate cup under the coffee delivery spout (e.g. coffee mug).
●
Press the button A repeatedly until the symbol for the ground coffee quantity is
displayed.
●
Then press the button and hold it pressed until the desired cup filling level is
reached.
●
Release the button. The new cup filling level is now stored.
Repeat the procedure if you also wish to change the filling level for the
other cup sizes.
All values remain stored even when the coffee machine is switched off.
Should you change your cup size, you can adapt the cup filling level
individually at any time or reset the filling level with a “Reset”. The settings
affected are described in section “RESETTING THE COFFEE MACHINE TO
FACTORY SETTINGS”.
The stored cup filling levels for each individual cup symbol only applies in
bean mode.
PREPARING COFFEE WITH POWDERED COFFEE
Ensure that you only use the measuring spoon supplied and never fill
than the container with more than one level measuring spoon (max. 8 g)
of coffee powder.
Do not fill the container with water-soluble, freeze-dried instant products
or other drink powders.
Too finely ground coffee powder can lead to faults.
To prepare coffee with powdered coffee, proceed as follows:
●
Select the “Coffee powder” function by pressing the button B . The following
appears on the display:
During preparation of coffee with powder, the “ground coffee quantity”
function is deactivated. Therefore no information on the ground coffee
quantity appears on the display.
Only one cup can be prepared with powdered coffee.
●
Select the desired cup size by pressing the button C . The following selections are
possible:
Coffee mug approx. 190 ml
Coffee cup approx. 120 ml
Espresso cup approx. 40 ml
The standard filling quantities for each single cup symbol apply to
bean, powder and hot water mode. If you wish to change the cup filling
quantities, they only apply to powder mode. Instruction can be found in
section “CHANGING AND STORING THE CUP FILLING QUANTITY IN
POWDER MODE”.
The following appears on the display:
●
Open the lid of the coffee bean container and the coffee powder shaft.
●
Pour in the fresh coffee powder.
●
Then close both lids again.
Ensure that powder does not clog the container and that no foreign matter
gets into the container.
Never fill the container with more than one level measuring spoon of coffee
powder.
The filling container is not a storage container; the powder must be
transported directly to the brewing unit.
●
Place a cup under the coffee dispensing spout.
●
In order to reduce heat loss and splashing, adjust the height of the dispenser to suit
your cup size by moving it up or down.
If the height adjuster is difficult to move, clean it. Proceed as described in
section “REMOVING AND CLEANING THE COFFEE DISPENSING UNIT”.
●
Press the button to dispense coffee.
You can stop coffee dispensing prematurely by briefly pressing the
menu button.
CHANGING AND STORING THE CUP FILLING LEVEL IN POWDER MODE
The coffee machine is set for standard quantities by default. However, you can set the cup
filling level individually for each cup size. Proceed as follows:
●
Select the “Coffee powder” function by pressing the button B .
●
Press the button C repeatedly until the required cup symbol for the desired ground
coffee quantity is displayed.
●
Place an appropriate cup under the coffee delivery spout (e.g. coffee mug).
●
Fill the coffee powder shaft with fresh powdered coffee.
●
Then press the button and hold it pressed until the desired cup filling level is
reached.
●
Release the button. The desired cup filling level is now stored.
Repeat the procedure if you also wish to change the filling level for the
other cup sizes.
All values remain stored even when the coffee machine is switched off.
Should you change your cup size, you can adapt the cup filling level
individually at any time or reset the filling level with a “Reset”. The settings
affected are described in section “RESETTING THE COFFEE MACHINE TO
FACTORY SETTINGS”.
The stored cup filling levels for each individual cup symbol only applies in
powder mode.
HOT WATER PREPARATION
Hot water from the steam nozzle can cause scalding. Avoid direct contact
with the skin.
To prepare hot water, proceed as follows:
●
Select the “hot water” function by pressing the button B . The following appears
on the display:
If the milk hose is connected, it must be disconnected from the frothing
nozzle before hot water is dispensed. Otherwise milk could be sucked in
unintentionally. See also section “CONNECTING THE MILK SYSTEM”.
●
Place a receptacle under the coffee dispensing spout.
●
Select the desired cup size by pressing the button C . The following selections are
possible: