Yolico YD3000N Series, Инструкция по эксплуатации

Страница: 71 / 139

SettingRange SettingRange
Disabled
Enabled
Description of choice Description of choice
Function Function
Sets integral control during acceleration/decelerationto
either enabled or disabled.
When “V/f control with PG feedback” is used, integral
control during acceleration and decelerationcan be enabled
or disabled with F1-07.Set F1-07 to “1” (integral control
enabled) if you want to keep the motor speed as close to
the frequencyreference as possible during acceleration
and deceleration. Set F1-07 to “0” (integral control disabled)
if you want to prevent the occurrence of overshooting/
undershooting.
SettingRange SettingRange
Function Function
Sets the overspeed detection method .
Function Function
Description of choice Description of choice
Sets the overspeed detection method .
Frequencies above that set for F1-08 (set as q a percentage
of the maximum output frequency),which continue to exceed
this frequencyfor the detection time (F1-09), aredetected
as overspeed faults.
SettingRange SettingRange
SettingRange SettingRange
Function Function
SettingRange SettingRange
Sets the speed deviation detection method .
Function Function
Description of choice Description of choice
Sets the speed deviation detection method .
F1-10 and F1-11 Settings . Constant F1-10 sets the PG
speed deviation detection level as a percentage of the
maximum outputfrequency. Constant F1-11 sets the
length of time in seconds that the difference between
the motorspeed and reference speed must exceed the
PG speed deviation detection level in order to detect
a Pgspeed deviation (DEV).
SettingRange SettingRange
Function Function
Sets the number of teeth on the gears if thereare gears between
the PG and the motor.
SettingRange SettingRange
Function Function
Description of choice Description of choice
Sets the number of teeth on the gears if thereare gears
between the PG and the motor.
When “V/f control with PG feedback” is used, the motor
can be operated even if there are gears betweenthe motor
and PG because the responsiveness is lower than it is
with vector control.Set the number of teeth on the gears
if there are gears between the motor and PG.
Motor speed (r ∕min) =
Number of pulses input from the PG × 60
Number of PG pulses (F1 −01)
×
Number of gear teeth 2 (F1−13)
Number of gear teeth 1 (F1−12)
A gear ratio of 1 (F1-12 = F1-13 = 1) will be used if either of these
constants is set to 0.
SettingRange SettingRange
Function Function
5 . 6 . 2Other Options Setup: F2 through F9 5 . 6 . 2Other Options Setup: F2 through F9
SettingRange SettingRange
Function Function
Description of choice Description of choice
3-channel individual
3-channel addition
Sets the functions for channel 1 to3 which are effective
when theAI-14B Analog Reference Card is used.
When using a AI-14B/A1-14U Analog Reference Card, set
constant b1-01 (reference selection) to “3”option).
When using a AI-14B, set the function for channels 1 to 3 with
constant F2-01. (There are no constantsto set for AI-14U.)
Constant b1-01 (reference selection) must be set to “1” (external
terminal), when 3-channel individualinput (setting: 0) is set.
When using a AI-14B and setting 3-channel individual input,
the multi-function inputs cannot be setto the Option/Inverter
selection function (setting: 2).
SettingRange SettingRange
Function Function
Description of choice Description of choice
BCD special setting
B
Binary input
Sets the Digital Reference Card input method .
When using a DI-08 or DI-16H2 Digital Reference Card, set
constant b1-01 (reference selection) to“3” (option) and set
the input method with constant F3-01.The maximum frequency
(100% speed) reference will be used when the binary input
is set (setting:7) and all bits are “1.”
• DI-08: Maximum output frequency reference (255/100%).
• DI-16H2: Maximum output frequency reference (16 bits:
30000/100%, 12 bits: 4095/100%).Setting 6, BCD special
setting (5-digit input), is valid only when the D1-16H2 is used.
Using this setting,a frequency from 0.00 to 399.98 Hz can be
set in BCD. The data input method is different from
that for
settings of 1 to 5.
PG disconnection detection time, in seconds
Is a registered trademark of yolico
YD3000N
نوﯾﺳﺎﻣوﺗا ﯽﺗﻌﻧﺻ
ﮏﯾرﺗﮑﻟاوﺑار
قرﺑ
و