Yolico YD3000N Series, Инструкция по эксплуатации

Страница: 69 / 139

SettingRange SettingRange
Set V / F curve
4
Function Function
SettingRange SettingRange
Function Function
Description of choice Description of choice
Constants E1-04 through E1-10 can be set by the user when
E1-03 has been set to “F.” These constantsare read-only
when E1-03 isn’t set to “F.”
When making the V/f characteristics a straight line, set the
same value in E1-07 (middle output frequency)and E1-09
(minimum output frequency). In this case, constant E1-08
(middle output frequencyvoltage) will be disregarded.
Set V / F curve
4
SettingRange SettingRange
Function Function
Description of choice Description of choice
Set V / F curve
Constants E1-04 through E1-10 can be set by the user when
E1-03 has been set to “F.” These constantsare read-only
when E1-03 isn’t set to “F.”
When making the V/f characteristics a straight line, set the
same value in E1-07 (middle output frequency)and E1-09
(minimum output frequency). In this case, constant E1-08
(middle output frequencyvoltage) will be disregarded.
SettingRange SettingRange
Function Function
Description of choice Description of choice
Constants E1-04 through E1-10 can be set by the user when
E1-03 has been set to “F.” These constantsare read-only
when E1-03 isn’t set to “F.”
When making the V/f characteristics a straight line, set the
same value in E1-07 (middle output frequency)and E1-09
(minimum output frequency). In this case, constant E1-08
(middle output frequencyvoltage) will be disregarded.
Set V / F curve
4
SettingRange SettingRange
Function Function
Description of choice Description of choice
Constants E1-04 through E1-10 can be set by the user when
E1-03 has been set to “F.” These constantsare read-only
when E1-03 isn’t set to “F.”
When making the V/f characteristics a straight line, set
the same value in E1-07 (middle output frequency)and
E1-09 (minimum output frequency). In this case, constant
E1-08 (middle output frequencyvoltage) will be disregarded.
Set V / F curve
4
Description of choice Description of choice
SettingRange SettingRange
5 . 5 . 4Motor 2 Setup: E5 5 . 5 . 4Motor 2 Setup: E5
Sets the motor rated current in 1 A units.
The setting range is 10% to 200% of the Inverter rated output
current.
The default setting depends uponthe Inverter capacity. (The
table
shows the default setting for 200Vclass, 0.4kWInverters.)
These values will automaticallybe set if they were set
duringautotuning.
Function Function
Description of choice Description of choice
Sets the motor rated slip in Hz units.
The default setting depends upon the Inverter capacity.(The
table shows the default settings for 200 V class, 0.4 kW
Inverters.)Calculate the rated slip (E2-02) from the value
shown on the motor nameplate with the following equationand
set this value.Rated slip = rated frequency (Hz) − rated speed
(r/min) × number of poles/120
SettingRange SettingRange
Function Function
T hese values will be automatically set during autotuning.
Sets the motor no-load current in 1 A units.
Description of choice Description of choice
Set the no-load current at the rated voltage and rated
frequency. Normally this value isn’tshown on the motor
nameplate, so it might be necessary to contact the motor
manufacturer.
SettingRange SettingRange
Function Function
Description of choice Description of choice
Frequency (Hz)
Output voltage (V )
User-defined V/f Pattern
Sets the number of motor poles .
Please be recorded in the motor on the motor poles (pole)
to set
SettingRange SettingRange
Function Function
Is a registered trademark of yolico
YD3000N
نوﯾﺳﺎﻣوﺗا ﯽﺗﻌﻧﺻ
ﮏﯾرﺗﮑﻟاوﺑار
قرﺑ
و