YOKOGAWA SMARTDAC+ GM Скачать руководство пользователя

Страница: 43 / 74

3-22

TI04L55B01-01EN

Program Control

Function

Description

Program RUN/RESET switch

Starts program operation when the input changes from off to

on.

Stops program operation when the input changes from on to

off.

Hold operation

Pauses the operation of program patterns when the input

changes from on to off.

Advance operation

Advances the operation of program patterns by one segment

when the input changes from on to off.

Start of program operation

Starts program operation when the input changes from off to

on.

Stop of program operation

Stops program operation when the input changes from off to

on.

Hold operation (specified loop, specified

program pattern)

Pauses the operation of the specified program pattern of the

specified loop when the input changes from on to off.

Advance operation (specified loop, specified

program pattern)

Advances the operation of the specified program pattern of

the specified loop by one segment when the input changes

from on to off.

Start of program operation (specified loop,

specified program pattern)

Starts the operation of the specified program pattern of the

specified loop when the input changes from on to off.

Stop of program operation (specified loop,

specified program pattern)

Stops the operation of the specified program pattern of the

specified loop when the input changes from on to off.

Program pattern number switch (binary/BCD

selection)

Switches the program pattern number according to the

combination of input ON/OFF states (binary or BCD).



Notification and Monitoring

Control status monitoring parameters and notifications (events) are output to DO or internal

switches (as actions).

Function

Description

Control status (RUN/STOP)

Outputs the control status (RUN status: ON, STOP status:

OFF).

Wait end signal (1s, 3s, 5s)

Outputs an ON state signal for 1, 3, or 5 seconds when the

program operation wait state ends.

Pattern end signal (1s, 3s, 5s)

Outputs an ON state signal for 1, 3, or 5 seconds when the

program operation ends.

PV event status

Outputs an ON state signal while a PV event is occurring

during program operation.

Time event status

Outputs an ON state signal while a time event is occurring

during program operation.

Wait flag

Outputs an ON state signal while the program operation is

waiting.

Hold-on flag

Outputs an ON state signal while the program operation is

being held.

Program operation mode monitoring (STOP/

RUN)

Outputs the program operation status (RUN: ON, STOP:

OFF)

Segment number monitoring (binary/BCD)

Outputs the running segment number in binary or BCD ON/

OFF states.

Pattern number monitoring (binary/BCD)

Outputs the running pattern number in binary or BCD ON/

OFF states.

Содержание SMARTDAC+ GM











































































Результаты поиска

Содержание SMARTDAC+ GM

Отзывы:

Похожие инструкции для SMARTDAC+ GM

Бренды по названию

Популярные бренды

YOKOGAWA SMARTDAC+ GM, Техническая информация

Результаты поиска

Содержание SMARTDAC+ GM

Отзывы:

Похожие инструкции для SMARTDAC+ GM

Бренды по названию

Популярные бренды