YOKOGAWA SMARTDAC+ GM Скачать руководство пользователя

Страница: 14 / 74

1-9

TI 04L55B01-01EN



Vehicles

Car air conditioner evaluation

• The GM is used to acquire in-car temperatures, duct temperatures and humidities, supplied

voltages, outside air temperatures, engine on/off state, and other types of data.

• The wide operating temperature range of -20 to 60°C enables testing in environmental test

labs, hot and cold regions, and so on.

• Monitoring on a tablet is possible with the Bluetooth (/C8) option.

Temperature

Tablet

Bluetooth

Inside a car

Humidity

Engine durability testing

• The GM acquires various types of data, such as air temperature, water temperature,

rotation, air volume, exhaust gas, in tests performed on engine test benches. Long-term

data acquisition is possible such as in durability tests performed by supplying rotation and

load control signals and varying the measurement conditions.

• Data acquisition is possible at different time intervals for each bench (multi-logging, (/BT

option)) by using the Data Logging Software GA10.

GA10

Multilogging

Bench 1

Bench 2

Bench 3

Block temperature

Water temperature

Oil temperature

Rotation

Air volume

Exhaust gas

concentration

Main unit

Sub unit

Ethernet

Bench 1

Bench 2

Bench 3

Test start

Test stop

What Is S GM?

Содержание SMARTDAC+ GM











































































Результаты поиска

Содержание SMARTDAC+ GM

Отзывы:

Похожие инструкции для SMARTDAC+ GM

Бренды по названию

Популярные бренды

YOKOGAWA SMARTDAC+ GM, Техническая информация

Результаты поиска

Содержание SMARTDAC+ GM

Отзывы:

Похожие инструкции для SMARTDAC+ GM

Бренды по названию

Популярные бренды