YOKOGAWA RC400G Скачать руководство пользователя страница 118

Страница: 118 / 141

<9. Troubleshooting>

9-3

IM 12F4A1-01E

(4) Error code “Err22” (sensitivity failure):

Conduct inspection following the inspection flow chart shown in Figure 9.2.

Confirmation Method

Confirm that the

calibration standard

solution concentration

is in the allowable

range.

Confirm the standard

solution concentration

by re-measurement.

Disposition

Check the metering

pump inspection

flow chart in

Figure 9.1.

Confirm the presence

of reagent in the

tank.

End

Set the span again, and recalibrate the

analyzer.

Adjust or replace the pump depending on the

inspection result.

Start

Is span setpoint

correct?

standard solution

concentration

accurate?

Is the

pump in normal

condition?

Is reagent

present in tank?

Polish the indicator electrode referring

to subsection 4.3.10. Clean glass beads

using the procedure described

in subsection 8.4. If not cleanable,

replace them.

Can

calibration be

performed?

Replenish reagent to the tank, and

recalibrate the analyzer.

YES

F9.2.ai

Is the

applied voltage

setup normal?

Is the voltage

being applied?

YES

Check the setpoint

using the operation

described in

subsection 5.3.2(3).

Measure the applied

voltage (between the

connecting terminals

ME and RE).

If setup is unsuitable, change it. If setting

cannot be carried out properly, further

adjustment or replacement of respective part

is necessary.

Malfunctioning of circuit, etc. is the cause of

the failure. Defective component must be

replaced.

Defective indicator electrode is the

cause of the failure. Replace the electrode.

(Note) When the determination of standard

solution concentration is carried out by

manual analysis other than

amperometric titration, change of the

reference sensitivity setup may be

necessary. Refer to subsection 7.3.

Figure 9.2

Sensitivity Failure Inspection Flow Chart

14th Edition : Jul. 15, 2020

Содержание RC400G














































































































































Результаты поиска

Содержание RC400G

Отзывы:

Похожие инструкции для RC400G

Бренды по названию

Популярные бренды

YOKOGAWA RC400G, Руководство пользователя

Результаты поиска

Содержание RC400G

Отзывы:

Похожие инструкции для RC400G

Бренды по названию

Популярные бренды