YOKOGAWA RC400G Скачать руководство пользователя страница 38

Страница: 38 / 141

<3. Installation, Tubing and Wiring>

3-13

IM 12F4A1-01E

3.3.1

Wiring for Power Supply and Grounding

This is for supplying power of voltage and frequency meeting the specification of the analyzer

and for grounding the converter case.
Connect the terminals L1 and L2 of the converter to power supply with a two-conductor cable of 6

to 12 mm finished O.D..
When the analyzer is equipped with arrestors (when option code “/ARS” is specified), connect

terminals L1 and L2 to the power terminal box (a circuit breaker is incorporated).
Refer to Figures 3.5 to 3.7.

CAUTION

The converter does not have a power switch. A double-pole switch should be installed in the

power line. A power switch for the converter is necessary to prevent electric shock or damage

to the instrument when inspection or maintenance of electric system is performed with power

supplied.

Treat the end of cable to be connected to the converter terminal in the following manner:
(1) Strip of the insulation covering from the cable at its end approx. 80 mm.

(2) Attach to the tip of the conductor a crimping type terminal lug which fits an M4 screw.

For grounding, use the grounding terminal marked “ ” at the bottom of the converter case.

Provide grounding by connecting the end-treated (for sufficient conduction) grounding lead to the

M5 screw of the grounding terminal (grounding resistance must be 100 Ω or less).

NOTE

When the grounding terminal of the converter case cannot be used, connect the grounding lead

to terminal G (M4 screw) inside the converter and ground the lead at the power supply. For this,

use a two- or three-conductor shielded cable for power supply and grounding wiring.

O1 O2

M1 M2

U1 U2

C1 C2

Power fuse

F3.6.ai

Figure 3.9

Wiring Terminals of Converter

14th Edition : Jul. 15, 2020

Содержание RC400G














































































































































Результаты поиска

Содержание RC400G

Отзывы:

Похожие инструкции для RC400G

Бренды по названию

Популярные бренды

YOKOGAWA RC400G, Руководство пользователя

Результаты поиска

Содержание RC400G

Отзывы:

Похожие инструкции для RC400G

Бренды по названию

Популярные бренды