Yingang YG125-30B Скачать руководство пользователя

Страница: 1 / 151

YG125-30B

Maintenance Manual

Foreword

Foreword

With the ever increasing varieties of motorcycles, new structures and new techniques have increasingly been applied.

To help YINGANG TECHNOLOGY Co., Ltd users and maintenance personnel better understand the maintenance,

adjustment and repair techniques of YG125-30A motorcycle, we prepared this maintenance manual. This manual is

expected to facilitate the YINGANG TECHNOLOGY Co., Ltd users and maintenance personnel and provide technical

guidance for them.

The masterstroke of the manual is the YG125-30A motorcycle , and the contents in Chapter 1-Chapter 3 are applicable

to the adjustment of various parts of the motorcycle. Chapter 4-18 describes various constituting parts of the motorcycle

respectively. Chapter 19 contains the electrical system diagram.

The standard maintenance procedures, maintenance precautions and general maintenance knowledge are not

covered in this manual. Any user or maintenance personnel who needs the above information may refer to the related

materials

All materials, charts and various data, as well as performance indices referenced herein, are for the latest model in our

product family at the date this manual is printed. YINGANG TECHNOLOGY Co., Ltd.

shall have the right

to, at any time,

amend this manual without prior notice. The copyright of all parts of this manual belongs to China YINGANG

TECHNOLOGY Co., Ltd.

and no units or individuals are allowed to reprint it the without consent of our company.

We hope you will enjoy the comfort and pleasure it brings to you during your driving!

Содержание YG125-30B
























































































































































Результаты поиска

Содержание YG125-30B

Отзывы:

Похожие инструкции для YG125-30B

Бренды по названию

Популярные бренды

Yingang YG125-30B, Руководство пользователя

Результаты поиска

Содержание YG125-30B

Отзывы:

Похожие инструкции для YG125-30B

Бренды по названию

Популярные бренды