Yingang YG125-30B страница 6 Скачать руководство пользователя

Страница: 6 / 151

YG125-30B

Maintenance

Manual

Overview

13. The clamp shall reliably bite the wire harness

In case of a welded clamp, it shall not bite the wire

harness towards the weld mark

The wire harness shall be clamped at the position

without contacting a rotating part or a removing element.

The wire harness shall be clamped at the position

without contacting a part that generates high

temperature.

The wire harness shall be clamped at the position

without contacting the edge or sharp corners of the

vehicle body.

The wire harness shall be incapable of passing through

the position contacting a bolt, a screw head or any front

part.

The wire harness shall not be slackened or be forcibly

pulled.

If the wire harness has to contact the edge or sharp

corner parts, the contacting part shall be protected with

hose or adhesive tape.

In case of a wire harness with garland, it shall be reliably

harnessed.

Do not damage the garnish of the wire harness.

Once the wire harness is damaged, repair it by coiling

with plastic adhesive tape.

While mounting parts and components, do not press the

wire harness.

Do not mount wire harness with it twisted.

Do not touch!

Do not pull!

Pay attention not to press it.

Содержание YG125-30B
























































































































































Результаты поиска

Содержание YG125-30B

Отзывы:

Похожие инструкции для YG125-30B

Бренды по названию

Популярные бренды

Yingang YG125-30B, Руководство пользователя

Результаты поиска

Содержание YG125-30B

Отзывы:

Похожие инструкции для YG125-30B

Бренды по названию

Популярные бренды