20
GB
O R I G I N A L I N S T R U C T I O N S
material, e.g. sandstone, asphalt or aerated concrete.
Take special care when you stop cutting. The cutting disc loses support in the workpiece being cut, which may result in jerking or
kickback towards the operator. Relieve the pressure on the disc when you stop cutting.
If water cooling has been used during cutting, dry the disc and the inside of the disc guard. After cutting, start the disc at full speed
for approx. 30 seconds, the air momentum will dry the disc and the inside of the disc guard.
When cutting is complete, hold the tool still, release the pressure on the switch and wait until the spinning of the disc has stopped
completely. Put the tool down. Disconnect the power cord plug from the power outlet and start maintenance works.
MAINTENANCE, STORAGE AND TRANSPORT
CAUTION! Before carrying out any adjustment, servicing or maintenance work, unplug the tool from the power outlet. Having
fi
nished working with the workpiece/material, inspect the power tool for damage by visually inspecting the exterior and the body
and the handles. Check the power cord, the plug, the action of the ON/OFF switch, the vents for clogging, the motor brushes for
sparking, the noise of the bearings and the drive transmission, and how the power tool starts and runs. During the warranty period,
the user is not allowed to install any power tools or replace any components or parts, as this will void the warranty rights. Any
abnormality found during this inspection or the operation require servicing at an authorized service agent’s. Having
fi
nished your
work, clean the housing, the vents, all switches, all handles and guards with compressed air at 0.3 MPa maximum, a brush or a
dry cloth. Do not use any chemicals or cleaners. Clean the tools and chucks with a clean, dry cloth.
The product should be stored thoroughly cleaned and dried. Store the product indoors. Secure against unauthorized access.
Ensure adequate ventilation to prevent water vapour condensation at the place of storage. The place of storage should protect
the product from weather conditions.
The product should be transported in unit packaging or other hard packaging, providing protection against shocks. Protect the
product from moisture during transport.
Spare parts
For a detailed list of spare parts for the appliance go to the “Download” section in the Product tab on the TOYA SA website: www.
toya.pl.
Содержание YT-82159
