YASKAWA PROFINET V1000 Скачать руководство пользователя страница 132 | Manualshive

Страница: 132 / 231

background image

A communications data error

occurred due to noise.

• Check the various options available to minimize the effects of noise.
• Counteract noise in control circuit, main circuit, and ground wiring.
• Use Yaskawa-recommended cables, or another type of shielded line. Ground

the shield on the controller side or on the drive input power side.

• Ensure that other equipment such as switches or relays do not cause noise and

use surge suppressors if required.

• Separate all wiring for communications devices from drive input power lines.

Install an EMC noise filter to the input side of the drive input power.

CF

Control Fault
A torque limit was reached continuously for three seconds or longer during a ramp

to stop while in Open Loop Vector Control.

CoF

Current Offset Fault
The current sensor is damaged or there was residual induction current in the motor

(e.g., during sudden deceleration or when coasting) when the drive attempted to

start the motor.

Cause

Possible Solution

Due to residual induction current in

the motor when the drive attempted

to start the motor, the drive

attempted to adjust the current

offset value beyond the allowable

range.

• Create a motor restart sequence that allows enough time for the residual

induction voltage to dissipate.

• Enable Speed Search at start (b3-01 = 1). Use the multi-function terminals to

execute External Speed Search 1 and 2 (H1-

oo

= 61 or 62).

Note:

When using a PM motor, both External Speed Search 1 and 2 perform the

same operation.

CPF02

A/D Conversion Error
An A/D conversion error occurred.

CPF03

PWM Data Error
There is a problem with the PWM data.

CPF06

EEPROM Data Error
There is an error in the data saved to EEPROM.

Cause

Possible Solution

Control circuit is damaged.

Cycle power to the drive. If the problem continues, replace the drive.

The power supply was switched off

when parameters were written (e.g.,

using a communications option

card).

• Cycle power to the drive and check operation again.
• Initialize the drive using A1-03.
• If the problem persists after initializing the drive, replace the drive.

CPF07

Terminal Board Communications Error
A communication error occurred at the terminal board.

CPF08

EEPROM Serial Communication Fault
EEPROM communications are not functioning properly.

CPF11

RAM Fault

CPF12

FLASH Memory Fault
Problem with the ROM (FLASH memory).

5.2 Fault Detection

132

YASKAWA ELECTRIC TOEP C710606 47A YASKAWA AC Drive – V1000 Quick Start Guide

«
...
130
131
132
133
134
...
»

Содержание PROFINET V1000








































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROFINET V1000

Standard Extreme RAKK dac Mark III

Бренд: Raleigh Audio Страницы: 65

Бренд: CEntrance Страницы: 14

Бренд: EMS Страницы: 18

Бренд: Tvone Страницы: 16

Al-Mu'allim AM-RD2

Бренд: PLAYNETICS Страницы: 21

Бренд: Katana Страницы: 162

Бренд: Hoymiles Страницы: 29

Бренд: Senci Страницы: 39

SinePower MSI924

Бренд: Waeco Страницы: 436

Бренд: ViewSonic Страницы: 44

Prizm 200750 Series

Бренд: Moog Страницы: 12

Бренд: CYP Страницы: 23

Бренд: Brunner Страницы: 8

Бренд: Fronius Страницы: 92

Бренд: DVDO Страницы: 9

Бренд: Santerno Страницы: 156

Бренд: Tektronix Страницы: 188

Бренд: Emergi-Lite Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды