YASKAWA PROFINET V1000 Скачать руководство пользователя страница 147

Страница: 147 / 231

EF4

External fault (input terminal S4)
External fault at multi-function input terminal S4.

EF5

External fault (input terminal S5)
External fault at multi-function input terminal S5.

EF6

External fault (input terminal S6)
External fault at multi-function input terminal S6.

EF7

External fault (input terminal S7)
External fault at multi-function input terminal S7.

FbH

Excessive PID Feedback
The PID feedback input is higher than the level set in b5-36 for longer than the time

set in b5-37, and b5-12 is set to 1 or 4.

FbL

PID Feedback Loss
The PID feedback input is lower than the level set in b5-13 for longer than the time

set in b5-14, and b5-12 is set to 1 or 4.

Hbb

Safe Disable Signal Input
The Safe Disable Input channel is open.

HbbF

Safe Disable Signal Input
The safe disable input hardware is defective.

HCA

Current Alarm
Drive current exceeded overcurrent warning level (150% of the rated current).

LT-1

Cooling Fan Maintenance Time
The cooling fan has reached its expected maintenance period and may need to be

replaced.

Note:

An alarm output (H2-

= 10) will only be triggered if H2-

= 2F.

LT-2

Capacitor Maintenance Time
The main circuit and control circuit capacitors are nearing the end of their expected

performance life.

Note:

An alarm output (H2-

= 10) will only be triggered if H2-

= 2F.

LT-3

Soft Charge Bypass Relay Maintenance Time
The DC bus soft charge relay is nearing the end of its expected performance life.

Note:

An alarm output (H2-

= 10) will only be triggered if H2-

= 2F.

LT-4

IGBT Maintenance Time (50%)
IGBTs have reached 50% of their expected performance life.

Note:

An alarm output (H2-

= 10) will only be triggered if H2-

= 2F.

Heatsink Overheat
The temperature exceeded the value set to L8-02.

oH2

Drive Overheat Warning
“Drive Overheat Warning” was input to a multi-function input terminal, S1 through

S7 (H1-

= B)

5.3 Alarm Detection

YASKAWA ELECTRIC TOEP C710606 47A YASKAWA AC Drive – V1000 Quick Start Guide

147

Troubleshooting

Содержание PROFINET V1000








































































































































































































































Результаты поиска

Содержание PROFINET V1000

Отзывы:

Бренды по названию

Популярные бренды

YASKAWA PROFINET V1000, Быстрый старт

Результаты поиска

Содержание PROFINET V1000

Отзывы:

Бренды по названию

Популярные бренды