YASKAWA PROFINET V1000 Скачать руководство пользователя страница 84

Страница: 84 / 231

No.

Display

Name

Function

–

Communication Port

Port used for USB Copy Unit, LCD Operator Keypad, and for

connecting to a PC.

NOTICE: Use only specified cable when making

connections to the drive. Failure to comply may damage

the drive.

NOTICE: Do not open the port cover wider than 90

degrees. Failure to comply may break the port cover and

leave the unprotected port susceptible to damage.

LED Screen Displays

Display

Lit

Flashing

Off

When the drive detects an alarm

or error

• When an alarm occurs
• oPE detected
• When a fault or error occurs

during Auto-Tuning

Normal state (no fault or alarm)

Motor is rotating in reverse

—

Motor is rotating forward

Drive Mode

Auto-Tuning

When DriveWorksEZ is used

<1>

Programming Mode

Displays output frequency (Hz)

—

As illustrated

in this

manual

STOP

<1>

Refer to the DriveWorksEZ instruction manual for further information.

4.1 Using the Digital LED Operator

YASKAWA ELECTRIC TOEP C710606 47A YASKAWA AC Drive – V1000 Quick Start Guide

Содержание PROFINET V1000








































































































































































































































Результаты поиска

Содержание PROFINET V1000

Отзывы:

Похожие инструкции для PROFINET V1000

Бренды по названию

Популярные бренды

YASKAWA PROFINET V1000, Быстрый старт

Результаты поиска

Содержание PROFINET V1000

Отзывы:

Похожие инструкции для PROFINET V1000

Бренды по названию

Популярные бренды