YASKAWA PROFINET V1000 Скачать руководство пользователя страница 188

Страница: 188 / 231

No.

Name

Description

H3-16

Terminal A1 Offset

Enter a 0 V signal to terminal A1. Next adjust the offset in H3-16

until the monitor U1-13 for the terminal A1 input voltage reads 0.0%.

The process is the same for terminal A2.

Note:

Available in drive software versions PRG: 1016 and later.

H3-17

Terminal A2 Offset

Enter a 0 V signal, and adjust the offset for terminal A2 in H3-17

until the monitor U1-14 for terminal A2 input voltage reads 0.0%.

Note:

Available in drive software versions PRG: 1016 and later.

H3 Multi-Function Analog Input Settings

H3-

Setting

Function

Maximum Input Level Possible

Frequency Bias

Max output frequency (E1-04).

Frequency Gain

Frequency reference (voltage)

Auxiliary Frequency Reference

(used as multi-step speed 2)

Max output frequency (E1-04)

Output Voltage Bias

200 V Class: 200 V

400 V Class: 400 V

Overtorque/Undertorque Detection Level

Open Loop Vector: Motor rated torque

V/f control: Drive rated current

PID Feedback

10V = 100%

PID Set Point

10V = 100%

Motor Temperature (PTC input)

10 V = 100.00%

Not used/Through Mode

–

FWD Torque Limit

Motor rated torque

REV Torque Limit

Motor rated torque

Regenerative Torque Limit

Motor rated torque

FWD/REV Torque Limit

Motor rated torque

Differential PID Feedback

10 V = 100%

30/31

DriveWorksEZ Analog Input 1/2

These settings are for analog output

functions used in DriveWorksEZ.

Normally there is no need to change or

apply these settings.

Output Voltage Gain

Note:

Function available in versions PRG: 1016 and later.

10 V = 100.00%

No.

Name

Description

H4: Multi-Function Analog Outputs

Use H4 parameters to configure the multi-function analog output terminals.

H4-01

Multi-Function Analog Output

Terminal AM)

Selects data output via multi-function analog output terminal AM.

H4-02

Multi-Function Analog Output

Terminal AM Gain

Sets terminal AM output level when selected monitor is at 100%.

B.1 Parameter Table

188

YASKAWA ELECTRIC TOEP C710606 47A YASKAWA AC Drive – V1000 Quick Start Guide

Содержание PROFINET V1000








































































































































































































































Результаты поиска

Содержание PROFINET V1000

Отзывы:

Похожие инструкции для PROFINET V1000

Бренды по названию

Популярные бренды

YASKAWA PROFINET V1000, Быстрый старт

Результаты поиска

Содержание PROFINET V1000

Отзывы:

Похожие инструкции для PROFINET V1000

Бренды по названию

Популярные бренды