YASKAWA E-V-SD Series Скачать руководство пользователя страница 23

Страница: 23 / 185

2.1 MECHATROLINK-

III

and Communications Settings

2-3

MECHA

TROLINK-

III

Communications

(1) JL100_USER_PAR Structure (Communications Parameter Settings)

This section describes the JL100_USER_PAR data structure.

JL100_USER_PAR

JL100_USER_IOMAP

C1 master

Slave #1

Slave #2

Slave #3

Slave #4

Slave #n

C2 master

CHANNEL_INFO

Write protected

Software settings

Allocated for the local station,
for each connected station,
and for the C2 master.

Software settings

Member Name

Description

Setting Example

Remarks

mod

Communications mode set-
ting

JL100_MOD_TYPE_C1MS
T | JL100_MOD_INT_FR

Master mode, hardware synchroni-
zation

ma0

Local station address

Master station (fixed)

ma_max

Maximum number of con-
nected slaves

As an example, the following five
axes are set: X, Y, Z, M, and SP.

t_mcyc

Transmission cycle (10 ns)

100000

1 [ms]

intoffset

Interrupt delay time (10 ns)

70000

700 [

c2_dly

C2 master send start time
(10 ns)

99500

Transmission cycle - 500 (10 ns)

prot_sel

Communications protocol
selection

Cyclic communications

max_rtry

Maximum retry times

1 retry

pkt_sz

Data length sent in one mes-
sage frame

64 bytes

wdt

WDT setting for host moni-
toring

1000

8 [ms] (1 = 8 [

s])

dly_cnt

Number of times to measure
transmission delay

1 time

Содержание E-V-SD Series


























































































































































































Результаты поиска

Содержание E-V-SD Series

Отзывы:

YASKAWA E-V-SD Series, Руководство пользователя, Страница: 23 / 185

Результаты поиска

Содержание E-V-SD Series

Отзывы: