YASKAWA CIMR-E7U Series Скачать руководство пользователя страница 12

Страница: 12 / 83

Connections 1-6

Serial Network Connections

The following describes how to connect the E7 drive to an RS232, RS422 and RS485 serial network. For detailed information please refer to the

appropriate sections of this manual or the

E7 Drive User Manual.

►

RS232 Networks

The RS232 network is a single ended network with limited data transmission rates and cable lengths. The E7 drive RS232 data transmission is

fixed at 9600bps, no parity, 8 data bits and 1 stop bit. The maximum cable length is 50 ft (16m). It is recommended that Yaskawa cables,

UWR00468-1 or UWR00468-2 be used. The UWR00468-1 cable can be used for both standard RS232 communications and for downloading

control software.

Figure 1.2 – RS232 Network Connection

►

RS422/RS485 4-Wire Networks

RS422/RS485 4-wire networks allow for longer cable lengths, maximum 4000 ft (1200m), and are more immune to noise than RS232 networks.

While RS422/RS485 4–wire may be used as multi-drop networks, however, single-ended networking is recommended. All RS422/RS485 4-wire

communication is half-duplex. Since each device is separately connected, set the Termination Resistor S1 to ON (slide the switch to the right) on

each device.

Figure 1.3 – RS422/RS485 4-Wire Network Connection

Содержание CIMR-E7U Series




















































































Результаты поиска

Содержание CIMR-E7U Series

Отзывы:

Похожие инструкции для CIMR-E7U Series

Бренды по названию

Популярные бренды

YASKAWA CIMR-E7U Series, Техническое руководство

Результаты поиска

Содержание CIMR-E7U Series

Отзывы:

Похожие инструкции для CIMR-E7U Series

Бренды по названию

Популярные бренды