Yamaha YZF-R6 Скачать руководство пользователя | Manualshive

Страница: 358 / 425

background image

8-2

Neutral indicator light “

”

High beam indicator light “

”

Turn indicator light “

”

Fuel indicator light “

”

1

2

3

4

Oil level / coolant temperature warning light “

”

Oil level symbol “

”

Coolant temperature symbol “

”

1

2

3

INSTRUMENT FUNCTIONS

ELEC

CAUTION:

NOTE:

INSTRUMENT FUNCTIONS

INDICATOR LIGHTS

Turn indicator light “

”

This indicator flashes when the turn switch is
moved to the left or right.

Neutral indicator light “ ”

This indicator comes on when the transmis-
sion is in neutral.

High beam indicator light “

”

This indicator comes on when the headlight
high beam is used.

Fuel indicator light “ ”

When the fuel level drops below approxi-
mately 3.7 L, this light will come on.
When this light comes on, fill the fuel tank at
the first opportunity.

OIL LEVEL / COOLANT TEMPERATURE WARNING LIGHT

This warning light has two functions.

The light will come on and symbol “

” will

flash if the engine oil level is low. If this sym-
bol flashes, stop the engine immediately
and fill it with oil to the specified level.

The light will come on and symbol “

” will

flash if the coolant temperature is too high.
The following chart shows the conditions of
the indicator light, symbol and temperature
display in accordance with the coolant tem-
perature.

Do not run the motorcycle until you know it
has sufficient engine oil.

Do not run the motorcycle if the engine is
overheated.

Even if the oil is filled to the specified level, the
warning light may flicker when riding on a slope
or during sudden acceleration or deceleration,
but this is normal.

«
...
356
357
358
359
360
...
»

Содержание YZF-R6










































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZF-R6

Бренд: hepco & becker Страницы: 4

Бренд: hepco & becker Страницы: 4

Burromini-Gas TT40

Бренд: Burro Max Страницы: 34

Бренд: R&G Страницы: 4

Бренд: RIEJU Страницы: 280

Бренд: tucanourbano Страницы: 4

Бренд: Benelli Страницы: 243

Бренд: Atra Страницы: 3

Бренд: APRILIA Страницы: 8

HeatProtech 3200

Бренд: MONNET Страницы: 17

Бренд: tucanourbano Страницы: 16

Termoscud R333EV

Бренд: tucanourbano Страницы: 28

Бренд: GripOne Страницы: 16

Бренд: Memphis Shades Страницы: 2

Бренд: Memphis Shades Страницы: 2

Бренд: JETPRIME Страницы: 4

Бренд: GAS GAS Страницы: 162

Бренд: KEEWAY Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды